Log:
Évaluations - 2, GPA: 3 ( )

Instructions Invacare, Modèle 1095340

Fabricant : Invacare
Taille : 177.25 kb
Nom Fichier : 1095349.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


SAVE THESE INSTRUCTIONS NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact Carrier/Invacare for further instructions. SAFETY SUMMARY The following recommendations are made for the safe and proper installation and use of the Contracture Footplate Retro Fit Kit: DO NOT install this equipment without first reading and understanding this instruction sheet. If you are unable to understand the Warnings, Cautions and Instructions, contact a healthcare professional, dealer or technical personnel if applicable, before attempting to install this equipment - otherwise, injury or damage may occur. GENERAL WARNINGS INSTALLATION WARNINGS After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely. This kit contains the following: DESCRIPTION QTY Contracture Assembly (Right Side) Contracture Assembly (Left Side) Insert Tube (Crossmember Assembly) Outer Tube (Crossmember Assembly) 1 1 1 1 INSTALLING THE CONTRACTURE FOOTPLATE ASSEMBLY Installing the Crossmember Assembly (FIGURE 1) NOTE: Refer to the GENERAL WARNINGSand INSTALLATION WARNINGSin theSAFETY SUMMARYof this instructionsheet. NOTE: Invacare recommends that two (2) people perform this procedure. NOTE: Take note of position and orientation of the mounting hardware for reassembly. 1. If necessary, remove the seating system from the wheelchair. Refer to the seating systems Owner’s Manual supplied with the wheelchair. 2. Remove the seat pan. Refer to REMOVING/INSTALLING THE SEAT PAN in PROCEDURE 4 of the Service Manual, part number 1085787. 3. Remove the back canes. Refer to REMOVING/INSTALLING THE BACK CANES in PROCEDURE 5 of the Service Manual, part number 1085787. 4. Remove the allen screw, spacer and locknut that secure the link bracket to the lower seat frame as shown in DETAIL “A” of FIGURE 1. 5. Remove the shoulder screw and locknut securing the rear of the seat frame to the bearing housing as shown in DETAIL “A” of FIGURE 1. 6. Repeat STEPS 4-5 for opposite side of seat frame. 7. Lift up to remove the seat frame from the base frame. NOTE: When reassembling the seat frame, the front crossbrace will be replaced with the crossmember assembly (insert tube and outer tube) provided in this kit and will be secured with the EXISTING mountingscrews. NOTE: Right and left sides of the seat frame are determined by sitting in the wheelchair. 8. On the left hand side of the seat frame, remove the two (2) EXISTING mounting screws and locknuts that secure the front and rear crossbraces to the brace supports of the seat frame as shown in DETAIL “B” of FIGURE 1. 9. Pull the left hand side of the seat frame away from the front and rear crossmembers. 10. Remove the EXISTING mounting screw, and locknut that secures the other end of the front crossbrace to the front right hand side brace support of the seat frame as shown in DETAIL “B” of FIGURE 1. 11. Remove the front crossbrace from the brace support and discard. 12. Insert one end of...

Ce manuel est également adapté pour les modèles :
Fauteuils roulants - 1095341 (177.25 kb)
Fauteuils roulants - 1095343 (177.25 kb)
Fauteuils roulants - 1095344 (177.25 kb)
Fauteuils roulants - 1095345 (177.25 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories