Évaluations - 1, GPA: 4
(
)
)
|
Facilité d'utilisation
960 Stewart Drive, Suite B Sunnyvale, CA 94085 USA Tel 1 ( 408) 730- 0950 • Fax 1 (408) 736- 0100 Visit our web site at: alliedtelesyn. com for all of our products. For details on the features and functions of your Allied Note Telesyn AT-WD1008 chassis and modules, refer to the following manuals from our The AT- WDRPS- 10 unit can be installed while the multiplexer is powered ON. web site: You do not need to power OFF the multiplexer to install the RPS. . AT-WD1008 Gigabit Ethernet Wavelength Division Multiplexer 1. Loosen the two thumbscrews that secure the blank faceplate over the right- Installation Guide hand redundant power supply expansion slot located on the front panel of the PN 613- 50367-00 AT-WD1008 Multiplexer and remove the cover. . AT-S47 Management Software User’s Guide PN 613- 50371-00 Package Contents Make sure the following items are included in the shipping package. If any item is missing or damaged, contact your Allied Telesyn sales representative for assistance. . One AT-WDRPS-10 Redundant Power Supply (AC) Module . One AC Power Cord . This installation guide . Warranty card 2. Remove the AT- WDRPS-10 unit from its shipping package. 3. Slide the AT-WDRPS- 10 unit into the RPS expansion slot. LNK TST TX RX LNK TST TX RX EAST TX SNMP MODULE ST TX RX RX TX CH 5 TX RX RX TX CH 6 TX RX RX TX CH 7 TX RX RX TX CH 8 TX RX FAN A FAN B POWERSUPPLY B WEST EAST NOR L LNK TST Installing the AT-WDRPS-10 Power Supply Overview The AT-WDRPS- 10 is an AC Redundant Power Supply (RPS) for the AT- WD1008 Multiplexer chassis. When installed, the unit shares the load of powering the chassis with the standard power supply that comes pre- installed in the chassis. If a power supply fails, the remaining unit provides all power to the system, thereby preventing a network failure. The power supply is hot- swappable, meaning that you can install it while the chassis is powered ON. Caution Before installing the module, refer to the AT-WD1008 Installation Guide for electrical safety and emission information. Caution Do not install the AT-WDRPS- 10 module in an AT-WD1008 chassis designed for DC power. An AC powered chassis has two AC power sockets on the back panel. LNK TST TX RX LNK TST TX RX EAST TX SNMP MODULE ST TX RX RXTX CH 5 TX RX RX TX CH 6 TX RX RX TX CH 7 TX RX RX TX CH 8 TX RX FAN A FAN B POWERSUPPLY B WEST EAST ORMAL LNK TST POWER FAULT AT-WDRPS-10 POWER FAULT AT-WDRPS-10 PN 613- 50369- 00 Rev A 1 2 3 4. Secure the AT- WDRPS-10 unit to the AT-WD1008 chassis by tightening the two thumbscrews. LNK TST TX RX LNK TST TX RX EAST TX SNMP MODULE ST TX RX RX TX CH 5 TX RX RX TX CH 6 TX RX RX TX CH 7 TX RX RX TX CH 8 TX RX FAN A FAN B POWERSUPPLY B WEST EAST NOR L LNK TST POWER FAULT AT- WDRPS-10 Note If you are installing the AT- WD1008 Multiplexer for the first time, refer to the AT-WD1008 Installation Guide for instructions on how to complete the installation. 5. Connect the power cord to the RPS AC power connector, located in the back of the multiplexer, and the other end of the cord to an appropriate AC power source. AT-WDFAN01 Power ON/ OFF Switch for AC Power Inlet AC Power Inlet Power ON/OFF Switch for the Optional for the Optional for the Standard the Standard RPS Module RPS Module Power Module Power Module 6. Turn the RPS power switch to the ON position. 7. Check that the POWER LED on the front of the RPS module is green. If the POWER LED is OFF or the FAULT LED is ON, refer to the AT-WD1008 Installation Guide for troubleshooting instructions. Note For added power protection to the multiplexer, the two AC power cords should be connected to power sources that are operating from different power circuits. This will protect the multiplexer from a power loss should one of the power circuits fail. This completes the installation procedure for the AT-WDRPS-10 unit. Technical Specifications Electrical Rating Input Voltage AC Input Frequency: Power Comsumption Environment Operating Temperature: Storage Temperature: Operating Relative Humidity: Storage Relative Humidity: Operating Altitude Range: 100 - 240 V AC, 3.2A maximum 47-63 Hz 75 watts maximum 0° C to 40° C ( 32° F to 104° F) -25° C to 70° C ( - 13° F to 158° F) 5% to 90% RH (non-condensing) 5% to 95% RH (non-condensing) Up to 3,000 m ( 9,843 ft) Electrical Safety and Emission Statement Standards: This product meets the following standards when installed in compliant host equipment. U.S. Federal Communications Commission RADIATED ENERGY Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residen...