Évaluations - 4, GPA: 4.5 ( )

Fabricant : Agri-Fab Taille : 3 mb Nom Fichier : Langue d'enseignement:

See figure 19. 35. Loop the 25" tarp strap under the hose. Hook to the hose hanger rod assembly. See figure 19. FIGURE 20 38. Assemble the hitch plate to the tractor hitch if: a. Your tractor has a square (straight) hitch frame, to help prevent binding. b. Your tractor has a lightweight hitch frame that needs reinforcing for towing the Chip-N-Vac. Use a 1/2" x 1-1/4" hex bolt, a 7/16" flat washer and a 1/2" nylock nut. See figure 21. TRACTORHITCH FRAME(SQUARE) HITCH PLATETRACTORHITCH FRAME(TAPERED) 1/2" x 1-1/4" HEX BOLT7/16" FLAT WASHER1/2" NYLOCK NUTATTACHMOW-N-VACHERE FIGURE 19 FIGURE 21 BEFORE PROCEEDING, look in the fold-out sheets to find the template for your mower deck. If written instructions are printed on the template, follow those instructions instead of the instructions in this manual. STOP ASSEMBLING THE DECK ADAPTER (#62468) TO THE MOWER DECK NOTE: Not all of the hardware will be used for any one particular fit up. 1. Identify and cut out the template for your brand and size mower deck. If there is no template included for your deck size, you can make your own template by marking around a piece of cardboard held against the edge of the deck's discharge opening. 2. FOLLOW THE INSTRUCTIONS PRINTED ON THE TEMPLATE. If there are no instructions, use the following instructions as a general guide. 3. Tape the template to the face of the adapter, about 1/2" from front and 1/4" down from top for deeper decks. For shallow decks, position template low enough that adapter will not extend below bottom of deck. Mark outline of template on face of adapter using white crayon, nail or scriber. Drill a starting hole inside the outline, then use a saber saw or key hole saw to cut out the opening. See figure 23. Contents of Hardware Pack for Deck Adapter: See Figure 22. REF. PART NO. QTY. DESCRIPTION A 43840 2 Hex Bolt, 5/16" x 1-1/4" B 43661 4 Hex Bolt, 1/4" x 1" C 43080 2 Carriage Bolt, 5/16" x 3/4" D 47810 3 Nylock Nut, 5/16" E 47189 5 Nylock Nut, 1/4" F 43088 9 Flat Steel Washer, 1/4" Std. G 43081 12 Flat Washer, 5/16" Std. H 1543-69 5 Nylon Washer I 23825 1 Mounting Strap J 23826 1 Angle Bracket K 23827 1 Mounting Bracket 1/4" DOWNKeep cut-off as close to the top edge as possible. IMPORTANT: 1/2" FROM FRONT IJKABCEDHGFNOT SHOWN FULL SIZESHOWN FULL SIZE FIGURE 23 PERFORM THIS STEP ONLY IF NECESSARY. 4. Remove the mower discharge deflector from your mower deck if necessary to attach deck adapter. Save the deflector and hardware for remounting deflector. FIGURE 22- FULL SIZE CAUTION: Mower deflector must be replaced when Vac System deck adapter is removed. Do Not operate mower unless adapter or deflector is in place and properly mounted. 5. Position the adapter over the deck opening, and check for fit of cutout as shown in figure 24. Trim cutout, if necessary, to allow tilting of adapter, keeping the fit as close as possible for best vacuum suction. 7. Assemble the adapter bracket to the deck using two 5/16" x 1-1/4" hex bolts, 5/16" flat washers and 5/16" nylock nuts. See figure 26. NOTE: It may be necessary to use extra 5/16" flat washers to shim under the bracket next to the deck surface. Ten extra washers have been furnished as shims. See figure 26. MOWER DECKDECK ADAPTERNOTE: Make sure adapter clears gauge wheels on mower deckCurl on deck may be located outside of adapter or inside depending on deck opening design ADAPTER BRACKET 5/16" flat washers used as needed for shims to adjust for variations in decks. (2) 5/16" NYLOCK NUTS 5/16" x 1-1/4" HEX BOLT(2) 5/16" FLAT WASHERS FIGURE 24 FIGURE 26 6. Holding the adapter bracket and the deck adapter together, position the deck adapter on the mower deck. Keeping the edge of deck adapter as close as possible to the offset in the adapter bracket, see if the slot in the adapter bracket can be aligned with one or two of the deflector holes in your mower deck's discharge opening. If the bracket can not be located correctly using existing holes, it will be necessary to drill one or two 5/16" diameter holes in the deck. See figure 25. 8. With deck adapter positioned correctly over the discharge opening, use the adapter bracket as a template and drill three 9/32" diameter holes in the top of the deck adapter. See figure 27. 9. Bolt deck adapter to bracket using three 1/4" x 1" bolts, nylon washers, 1/4" flat washers and 1/4" lock nuts. Nylon washers should be against the inside of the deck adapter. See figure 27. 10. Assemble end of hose and a hose clamp over the round opening of deck adapter and tighten clamp. GO DIRECTLY TO THE OPERATION INSTRUCTIONS ON PAGE 15. DECK ADAPTERMOWER DECKADAPTER BRACKETKeep edge of adapter as close as possible to offset in bracketUse existing holes or drill 5/16" diameter hole or holes. (3) 1/4" NYLOCK NUTS (3) NYLON WASHERS (3) 1/4" STEEL WASHERS (3) 1/4" x 1" HEX BOLTSADAPTER BRACKET MOWER DECK DECK ADAPTER FIGURE 27 FIGURE 25 OPERATION HOW TO USE YOUR CHIP-N-VAC BEFORE STARTING 1. Your Chip-N-Vac engine is shipped without oil or gaso...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :