Évaluations - 3, GPA: 4.7 ( )

Fabricant : MTD Taille : 1.82 mb Nom Fichier : Langue d'enseignement:

Keep proper balance and footing at all times. • The engine governor settings on your machine must not be altered, changed, or tampered with. The governor controls the maximum safe operating speeds and protects the engine and all moving parts from damage caused by overspeed. • Do not transport machine while engine is running. • Do not operate engine if air cleaner or cover directly over carburetor air intake is removed, except for adjustment. Removal of such parts could create a fire hazard. MAINTENANCE AND STORAGE • When this equipment is stopped for servicing, inspection, storage or to change an accessory, make sure the spark plug wire is disconnected from the spark plug and moved away from the spark plug. The machine should be allowed to cool down before making such inspection, adjustments, service, etc. Maintain your machine with care and keep it clean for the best and continued safe operation. • Do not use flammable solutions to clean the air filter. • When not in use, your machine should be stored out of the reach of children. Keep where gasoline fumes will not reach an open flame or spark. For long periods of storage, refer to the “Off-Season Storage” section of this manual. 2 ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil recommendations. NOTE: To determine right and left hand sides of your shredder, stand behind and face the hopper (engine is at the front of the unit). TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches or Adjustable Wrenches Your shredder has been completely assembled at the factory, except for the chute deflector and the catcher bag. A pair of safety glasses are also included in the carton. TO REMOVE SHREDDER FROM CARTON Cut the corners of the carton. Remove all packing inserts. Roll shredder out of carton. Make certain all parts, literature and the safety glasses have been removed before the carton is discarded. All hardware has been placed in position on the shredder. TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches or Adjustable Wrenches Spacers (Inside Hinge) Hex Bolt Chute Deflector N FIGURE 1. Drawstring Plunger Catcher Bag A WARNING: Make certain the spark plug wire is disconnected and moved away from the spark plug before assembling the shredder. ATTACHING THE CHUTE DEFLECTOR (Hardware B) "(See Figure 1) 1. Remove the hand knobs and cupped washers from each side of the discharge opening on the left side of the shredder. 2. Remove the hex lock nut, two spacers and hex bolt from inside the hinge on the chute deflector. Do not remove one spacer from the hex bolt. 3. Place the chute deflector in position on the discharge opening. Insert bolt through hinge on chute deflector and housing (spacer fits inside hinge). 4. Place the second spacer over the hex bolt, inside the other part of the hinge. Secure with hex lock nut. Tighten securely. 5. Secure both sides of the chute deflector to the housing using the hand knobs and cupped washers (cupped side of washers go against the chute deflector). A WARNING: Do not operate this shredder unless chute deflector has been properly installed and secured with hand knobs. FIGURE 2. ATTACHING THE CATCHER BAG Your shredder is equipped with a catcher bag to catch the shredded material. To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening. Depress the plunger on the drawstring, pull on the drawstring until the bag is tight around the chute opening. Release plunger to lock it into position. ■See figure 2. OPERATION KNOW YOUR SHREDDER READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SHREDDER. Compare the illustrations with your shredder to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Hopper Assembly Chipper Chute Spark Plug Starter Handle FIGURE 3. FIGURE 4. OPERATING CONTROLS (See figures 3 and 4) CHOKE LEVER—Used to enrich the fuel m xture in the carburetor when starting a cold engine. STARTER HANDLE—Used to manually start the engine. THROTTLE CONTROL—Controls engine sp 3ed and stops the engine. The operation of any shredder can resul in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses > or eye shields. We recommend wide vision safety mask for over spectacles or standard safety glas ses. BEFORE STARTING 1. Place the shredder on a firm, level surface. 2. Service engine with gasoline and oil as instructed in the separate engine manual packed with your shredder. 3. Attach spark plug wire to spark plug. NOTE: Check the fuel level periodically to avoid running out of gasoline while operating the shredder. If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit before it can be restarted. Refer to “Removing the Flail Screen” on page 6. TO ST...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :