Please come and visit us. te call your machine fhe PTO HORSE Model •BILT® Roto Tiller-Power Composter hout this Owner/Operator Manual and in r literature, we refer to your machine as the RSE Model”. The name aptly describes its se ruggedness, and it distinguishes this m the smaller ECONO-HORSE, PONY® and models, as well as from other models that n available in the past or that might be I in the future. tory dates back to the old Rototiller Corpo-5 company that introduced rear-tine rotary til

This places the transmission in the correct position to take a “Cold” oil level reading. 3. Allow the tiller to rest in this position for at least five minutes for a “Hot” reading or two hours for a “Cold” reading. (Allow more time if the air temperature is below 40 °F). 4. Clean the area around the tine attachment dipstick so that no debris will fall into the transmission. 6-8: Tine attachment dipstick markings. 5. Using a 9/16-inch wrench, remove the dipstick as shown in Photo 6-7. Wipe th

See Figure 5. b. Pull spring loaded pin out on the base and align pin with the first hole (closest to the end of the tube) in the hose adapter. c. Release the pin to lock the hose in place. 3 Setting Up Your Yard Vacuum IMPORTANT Make sure the cables are routed outside the lower handle. Also, do not crimp the cables while lifting up the handles. A B Rope Guide A B Figure 6 6. a. Snap the hose handle first into the upper hose handle bracket and then into the lower hose handle bracket. See Figure

See Figure 23. 10.The nuts on the flat head cap screws can be reached from underneath using a 1/2-inch socket, universal, and extension. See Figure 24. 11. Replace or sharpen chipper blade. The blade can be sharpened with a file or on a grinding wheel. 12.When sharpening blade, protect hands by using gloves and follow the original angle of grind. 13.Reassemble by performing the previous steps in the opposite order and manner of removal. NOTE: Tighten blade screws to 210 - 250 in-lbs. Make certai

Check their proper operation regularly. 2. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed. 3. Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. 4. Do not change the engine governor settings or ove

Compare the illustrations in Figure 4 with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Engine Controls See the Briggs & Stratton Owner/Operator manual packed with your unit. for the location and function of the controls on the engine. Starter Handle The starter handle is located on the engine. Pull the starter handle to start engine. See Figure 4. Spring Latch The spring latch is located on the top of the hopper.

....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. PRINTED IN U.S.A. TROY BILT LLC, P.O. B

For best performance, it is also important to keep the chipper blade sharp. Keep bystanders, helpers, pets, and children at least 75 feet from the machine before starting and while operating. Do not operate this machine unless the discharge chute and bag have been properly installed and secured to the machine. Setting Up Your Chipper Shredder Vacuum 4 WARNING Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while

This unit has been designed, engineered and manufactured to give you the best possible dependability and performance. Please carefully read this Manual. It tells you how to safely and easily assemble, operate and maintain your machine. Be sure that you and any other operators carefully follow the recommended safety practices at all times. Failure to do so could result in personal injury or property damage. Please complete and return the Owner Registration Card that is included in the literatur