Évaluations - 2, GPA: 4 ( )

Fabricant : Southbend Taille : 1.05 mb Nom Fichier : 1177596_web.pdf Langue d'enseignement:

Remove all wood blocking, packing material and accessories. 2. The legs should be installed after the unit has been uncrated, near the area where it will be used. 3. Raise unit sufficiently to allow legs to be installed with four bolts. 4. The legs can be adjusted to overcome an uneven floor. Use a spirit level in all directions on the middle oven rack. 5. When casters are supplied, the locking swivel type casters should be installed in the front 6. Casters are provided with a zeric fitting for lubrication. When a Bft truck or other mechanical means are not available, and manual labor is involved, please consider the following suggestions, 1. Raise each comer or, if feasible, raise an entire side by “leaning* the unit 2. For safety, "shorn up” and support the raised section with an adequate blocking arrangement strong enough to support the load 3. When long legs are being installed and the unit must be tipped beyond the stable point, lean unit against a strong wall or other suitable structure to prevent it from ‘tailing over" 4. When absolutely necessary and unit must be placed “completely over," lay ONLY on its LEFT side. Take care to protect finish on left side. 5. Bring unit to its straight position gently. NEVER DROP, or allow unit to PALL NOTE: An ‘open” storage rack arrangement may be incorporated on units supported by high legs. Directions and illustrations are provided on another sheet and are also provided with these parts. Refer to diagram titled Assembly for open rack storage in the installation section of this manual. Adequate restraining means must be attached to rear of appliance when installed, installation must conform to local codes as applicable. Awarning For an appliance equipped with casters,instructions shall be that installation shall be made with a connector that complies with the Standard for Connectors for Moveable Gas Appliances, ANSI 221.69 or Connectors for Movable Gas Appliances, CAWCGA-6.16-M87, and a quick-disconnect device that complies with the Standard for Quick-Disconnect Devices for Use With Gas Fuel, ANSI 221.41 or Quick-Disconnect Devices for Use with Gas Fuel, CAN1-6.9, adequate means must be provided to limit the movement of the aplliance without depending on the connector and the quick-disconnect device or its associated piping to limit the appliance movement. Awarning If disconnection of this restraint is necessary to move the appliance for cleaning, etc., reconnect it when the appliance is moved to it originally installed position. PAGE 9 INSTALLATION INSTALLATION LEGS FOR SINGLE DECK OVENS ITEM FART NUMBER DESCRIPTION + 1146213 3/8 x 16 x 1 Hex Head Bolt ■» 1146513 3/s Lock Washer * 1146522 3/8 Rat Washer A 1175090 Single Deck Adj. Leg B 1174266 Adj. Foot for Leg t 1173584 Flanged Foot for Leg * Not shown (qty. 16 used per unit to attach legs to unit) t Flanged Foot is optional replacement tor 1174266 FIGURE 3 CASTERS FOR SINGLE DECK OVENS ITEM PART NUMBER DESCRIPTION * 1146213 3/8x16x1 Hex Head Bolt * 1146513 3/8 Lock Washer * 1146522 3/8 Flat Washer A 117SQ89 Single Deck Caster Leg 6 1174263 Caster less Brake C 1174264 Caster with Brake t 1174265 Caster Package * Not shown (qty. 16 used per unit to attach tegs to unit) t This package contains 4 casters, 2 with locks, 2 with out locks no legs pads, bolts or washers am included with this package. U FIGURE 4 PAGE 10 LEGS FOR DOUBLE STACKED OVENS ITEM PART NUMBER DESCRIPTION * 1146213 3/8x16x1 Hex Head Bolt * 1146513 3/8 Lock Washer * 1146522 3/8 Flat Washer A 1172788 Leg Pad B 1174259 SS Leg, 3/4 Stud t 1174260 Leg Package * Bote, lock washers, and flat washers not shown. Requires 4 of each per pad for a total of 16 each per double oven. . tThis package consists of 4 legs only. No leg pads, bolts or washets are included in this package. FIGURE 5 NOTE: Leg Pads (Item A) are installed on oven at factory when units are ordered stacked. CASTERS FOR DOUBLE STACKED OVENS ITEM PART NUMBER DESCRIPTION * 1146213 3/8x16x1 Hex Head Bolt * 1146513 3/8 Lock Washer * 1146522 3/8 Rat Washer A 1172788 Leg Pad B 1174263 Caster less Brake C 1174264 Caster with Brake t 1174265 Caster Package * Bolts, lode washers, and flat washers not shown. Requires 4 of each per pad for a total of 16 each per double oven. tThis package consists of 4 legs only. No leg pads, bolts or washers are included in this package. FIGURE 6 PAGE 11 INSTALLATION INSTALLATION A WARNING For an appliance equipped with casters, the installation shall be made with a connector that complies with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69, or Connectors for Movable Gas Appliances, CAN/CGA-6.16-M87, and a quick-disconnect device, that complies with the the Standard for Quick-Dlsconnect Devices for Use with Gas Fuel, ANSI Z21.41 or Quick-Disconnect Devices for Use with Gas Fuel CAN1-6.9. Adequate means must be provided to limit the movement of the appliance without depending...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :