Évaluations - 3, GPA: 4.3 ( )

Fabricant : Indesit Taille : 233.79 kb Nom Fichier : Langue d'enseignement:

We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance. In all cases adhere to routing details (see fig. 5). This appliance must not be installed over any other appliance that generates heat such as a plinth heater. Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable. GENERAL The appliance is designed to be mounted on a floor between two adjacent cabinets. The cabinets must be securely fixed to the wall and the cooker securely fixed to the cabinets. This cooker must not be used free standing. Note; This cooker must not be fitted on a platform. FINAL INSTALLATION a. Ensure that the adjacent cabinets and the gap between them have dimensions in accordance with the diagram. b. Assemble the plastic plugs provided into the fixing brackets. See diagram. c. Fix the fixing brackets to the sides of the adjacent cabinets so that the centre line of the brackets are 570mm above the top of the plinth line and the front face of the plastic plug is level with the front face of the cabinet sides. See diagram. d. Adjust the feet on the cooker to their minimum position, i.e. fully screwed in. e. Slide the cooker centrally into the space between the cabinets ensuring the following: i) The gap between the cabinet sides and the cooker is even along the length of the cabinet sides. ii) The cable is routed away from any vents in the rear panel and is not trapped between the cooker and the wall, adjacent cabinets or under the feet f. Adjust the feet using an open ended spanner until the bottom of the cooker door is in line with the top of the plinth. Using a spirit level, check that the cooker is level in all directions. g. Check that the plinth can be fitted. If necessary re -adjust the feet and check that the cooker is level. Then lock the feet into position by tightening the lock nut using an open ended spanner. h. Open the top oven door and fix the cooker to the brackets through the holes in the side trims. i. Fix the plinth in position. j. Ensure that there is a minimum gap of 1mm between the cooker side trim and the adjacent cabinet doors or drawer fronts. k. If a hob is to be installed directly above the cooker it must not project downwards more than 20mm below the underside of the work top. Any projection of more than 10mm must not project more than 500mm from the wall. Fig. 5 GB 21 Installation GB 597mm min 890mm Max870mm Min 720mm min 570mm 150mm min 170mm max A minimum distance of 25mm should be maintained between the front face of the cabinet side and the front face of the plinth. 22 If Something Goes Wrong? Before calling a Service Engineer, please check through the following lists. THERE MAY BE NOTHING WRONG. GB . . +8 9& + 8 8 . This is normal and should cease after a short period. . If you find :Display is blank. $ ( (((&. Check: (i) That the main cooker wall switch is turned on. (ii) Check other appliances to see if you have a power cut. (iii) Check the main circuit breaker for the property. $ (:0.00 $%: The power supply to your oven has possibly been interrupted, but has now come back on again. Reset the timer to the correct time of day and "Manual" operation using the instructions given in the timer section of the book. %&+ +$%& . 8 + Check that the Auto Symbol is not lit up and is not flashing. 8 ::. $%&+ + %&. Operating the cooker under the following conditions may cause a safety device to operate. (a) Grilling with the door closed - always grill with the door open to the correct position - see grilling (b) Grilling for an excessively long period at maximum setting - see grilling guide. (c) Grilling with inadequate ventilation in the cabinet - see installation instructions. +88 When the "Grill" control (A) is operating at less than MAX, the grill will cycle on and off, this is normal and is not a fault. :: . Remember: "Cook Period" is the actual length of time for which, the timer will switch the oven(s) on as part of an "Auto Cooking" programme. 8 . . A gentle flow of air will be blown from beneath the control panel when the appliance is used. If the appliance is still warm, this cooling fan may run on, or restart itself after all of the controls have been turned off. The fan will stop once the appliance has been cooled. This is normal and not a fault. $ ;;9 ( Press the minute minder button to silence the Buzzer/Bleeper. If you have been through the above list and there is still a problem, contact Service (see Back Page). 23 If it Still Won't Work GB Contact the Service Office If something is still wrong with your appliance after you have been through the 'Something Wrong' list: 1. Switch off and unplug the appliance from the mains. 2. Call your nearest Service Office or local importer. When you contact us we will want to know the following: 1. Your name, address and postcode. 2. Your te...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :