Évaluations - , GPA:
(
)
)
Fabricant : CDA
Taille : 1.02 mb
Nom Fichier : 60d35e47-a9b1-4dd6-8304-a0a56f319fc6.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
These are explained below: Conventional Oven This function uses the top and bottom heating elements with a temperature between 50OC and Max. Natural convection creates a perfect cooking zone in the centre of the oven. Lower element This function uses the bottom heating element with a temperature between 50OC and Max. This function is ideal for cooking foods that require a greater heat underneath. Upper element This function uses the upper heating element with a temperature between 50OC and Max. This function is ideal for cooking foods that require a greater heat above. Grill This function radiates the heat from the grill element. The grill must be set at 200OC. Please note: • Always grill with the oven door closed. • Put the grill pan as close to the grill as possible. • Do not grill for more than 30 minutes at a time. • Preheat the grill for approximately five minutes with the oven door closed. Temperature knob • To set the temperature, turn the temperature knob clockwise to the required temperature. • Once the oven has reached the required temperature, the temperature indicator lamp on the control panel will switch off. • The temperature indicator lamp will light up when the oven elements are working. Changing the Oven Lamp Before any maintenance is started involving electrical parts, the appliance must be disconnected from the power supply. If the oven has been in use, let the oven cavity and the heating elements cool down before attempting any maintenance. Changing the bulb (fig. 1) • Unscrew the protective cover. • Unscrew and replace the bulb with the new one suitable for high temperatures (300oC) having the following specifications: 230-240V 50Hz, 15W, E14. • Refit the protective cover. fig. 1 IMPORTANT: Never use screwdrivers or other utensils to remove the light cover. This could damage the enamel of the oven or the lamp holder. Remove only by hand. Please note: The bulb replacement is not covered by your guarantee. Cleaning and Maintenance - Removing the Oven Door The oven doors can easily be removed as follows: • Open the door fully. • Open the lever on the left and right hinges (as show in figure 2). • Gently close the door until left and right hinge levers are hooked to the door. • Lift the door by removing the hinge hooks from their location in the direction indicated. • Rest the door on a soft surface. • To replace the door, repeat the above steps in reverse order. fig. 2 Cleaning and Maintenance - Removing the Oven Door Inner Glass To remove the inner pane of the top oven door on both sides 1. Remove the oven door as shown below. 2. Release the two upper blocks by pressing down as shown in fig. 3. 3. Slide the door glass out in the direction shown in fig. 3.1. 4. Clean the glass with an appropriate cleaner, dry thoroughly and place on a soft surface. 5. Now you can also clean the inside of the outer glass. To replace the inner glass 1. Ensuring the OK symbol on the glass is facing you, slide the glass back into the frame. 2. Replace the upper blocks, ensuring they lock back into place. 3. Replace the oven door. IMPORTANT: Do not clean the glass whilst it is still hot. Please keep the ok symbol to the bottom right of the oven door (fig. 3.1). fig. 3 fig. 3.1 If the oven is being installed into a built under oven housing unit ensure that the front rail at the top of the unit is not Ensure that air can flow freely around the housing area. If the oven is being installed into a fully enclosed built-under oven housing unit it may be necessary to cut a small slot in the top of the plinth fitted under the unit. Cut a section 400mm wide and a minimum of 15mm high to allow air to pass under the unit. Alternatively cut a section 400 x450mm in the base of Failure to allow adequate ventilation to the appliance may result in overheating or damage to adjacent units and could The walls of the kitchen units must be able to withstand temperatures of 75oC above ambient (typically this is between When correctly installed ensure that there is a gap of 4mm minimum between the sides of the oven and adjacent Lift the oven carefully into position on the shelf, taking care NOT to lift it by the door handle. If you lower the oven door, you will see 4 screw holes, 2 on each side of the oven. The oven should then be secured to the housing by fitting screws into these holes. Remember the housing should not be free standing but be secured to the wall and/or adjacent fittings. 400560560 56045057557510056045049920-24598594558573fig. 4 If the oven is being installed into a built under oven housing unit ensure that the front rail at the top of the unit is not Ensure that air can flow freely around the housing area. If the oven is being installed into a fully enclosed built-under oven housing unit it may be necessary to cut a small slot in the top of the plinth fitted under the unit. Cut a section 400mm wide and a minimum of 15mm high to allow air to pass under the unit. Alternatively cut a section 400 x450mm in the base of Fa...