Évaluations - 3, GPA: 4.7 ( )

Fabricant : Amana Taille : 1.24 mb Nom Fichier : Langue d'enseignement:

Children climbing on the range to reach items could be seriously injured. Range should extend approximately 2 inches from cabinet front to oven door handle. Using dimensions, prepare cabinet opening. l c ,s,, "'S _301/8 to 301/4inches B 36inches standard C 35 inches standard D 23inches standard E 25 inches standard Minimum Clearances to Combustible Surfaces Using dimensions, prepare cabinet opening. • Minimum clearance to rear wall is 0 inches. • Minimum clearance to a vertical right or left side wall is 0 inches. • Minimum clearance to countertop/cabinet on each side is 0 inches. • Minimum of 30 inches between top of cooking surface and bottom of an unprotected wood or metal cabinet. • Minimum of 24 inches between cooking surface and protected wood or metal cabinet above range. Cabinet bottom must be protected by at least 1/4inch thick millboard with not less than No. 28 MSG sheet steel, .015 inch thick stainless steel, .024 inch thick aluminum, or .020 inch thick copper. A 30 inches minimum B 30 inches unprotected/24 inches protected minimum C 13 inches maximum D 25 inches maximum _36 inches maxinmm Minimum Clearances to Combustible Surl_aces Standard Cabinet and Countertop Height 5 Irregular Cabinet and Countertop Heights Countertops such as ceramic tile tops cause cabinet and countertop to be higher than 36 inches. Follow instructions below when countertop is higher than 36 inches. 1. Raise leveling legs to maximum height. 2. Measure from floor to rangetop. If measurement is less than height of countertop, floor must be shimmed. 3. Shim floor using a piece of plywood same size as range opening. Secure plywood to floor. Plywood must be as secure as original flooring. 4. Install anti-tip bracket and slide range into place. Line Voltage Requirements Line voltage must not exceed rated voltage. See rating plate attached to range for kilowatt rating. Line voltage less than rated voltage will result in slow heating. Wiring system must conform to Underwriters Laboratories, Inc. standards and National Electrical Code. Installation must conform to all local, municipal and state building codes, and local utility regulations. Range must be connected only to a supply circuit as specified on rating plate wiring diagram of range. Range requires 3 wires, 120/240 Volts 60 Hertz A.C. House wiring and fusing must comply with local wiring codes. If no codes apply, wire according to National Electrical Codes. Power Supply Location Shaded area show range clearance for electrical connection. Power Cord Requirements Power cord is not supplied with range. Power cord must be U.L. Listed and meet NEC and Mobile Home Manufacturers Association Standards. Cord must be rated at a minimum 250V_40 AMP, equipped with a plug configuration in accordance with NEMA. Conductors must end with closed loop (ring) terminals at the range. • Three-conductor cord plug NEMA 10-50P allowed for residential. • Four-conductor cord plug NEMA 14-50P required for most mobile home installations but can be used for residential. NOTE: Only a power cord suitable for use with ranges may be used. For installation in a mobile home, or area where local codes do not permit grounding through the neutral terminal, a 4-wire cord must be used. Range Terminal Block Connection block is located at bottom rear of range behind rear cover panel. Remove rear cover screw. Directly below terminal block is a hole for a power supply service cord. Power cord is not supplied with range. Attach Power Cord A 3 inches B 7 inches 6 inches D 30I/8 inches mininmm _24_/16 Power Supply Location Range has been grounded at the factory to the center (nickel plated) terminal of the terminal block in accordance with the National Electrical Code (section 2560). When a separate ground is required by local code, disconnect the grounding strap from the terminal block. Ground frame by connecting a grounding wire to range frame using only the grounding screw removed from the grounding strap. Neutral terminal connect wire with white insulation Power terminals (240 V) \ Ground strap Power lead connect wire with black or red insulation and brass terminal Terminal Block Terminal block is approved for copper wire connection only, NOT aluminum wiring. If aluminum house wiring is to be connected, the following procedure is suggested. 1. Connect length of copper building wire to range terminal block with ring terminals. 2. Splice copper wires to aluminum wiring using connectors which are designed certified by Underwriter's Laboratories and recognized for joining copper to aluminum. Follow the connector manufacturer's recommended procedure. 3. Wire used, location and enclosure of splices must conform to local codes. Installing 3-Wire Power Cord Refer to power cord instructions if available for additional information. 1. Remove rear wire cover on rear of range. 2. Place strain relief (winged clamp) in cord access hole below terminal block. • Strain relief is supplied with cord. Place wings through hole, enteri...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :