Évaluations - 5, GPA: 4.4
(
)
)
|
Facilité d'utilisation
ES7G16 Before operating this unit, please read these instructions completely. Thank you for purchasing the Panasonic Wet/Dry Rechargeable Shaver Model No.ES7G16. P01-04(ES7016№t|) 02.1.31 19:50 ^^4 Index ENGLISH Page 5 DEUTSCH Seite g FRANÇAIS Page 14 ITALIANO Pagina 19 NEDERLANDS Pagina 24 ESPAÑOL Pagina 29 DANSK Side З4 PORTUGÊS Pagina 38 NORSK Side 4З SVENSKA Sid 47 SUOMI Sivu 51 POLSKI Strona 55 CESKY Strona 6G MAGYAR Oldal 64 ROMANA Pagina 69 РУССКИЙ Страница 74 4 ■ШШ] ■ I I I I 4- I Before use This Wet/Dry shaver can be used for wet shaving with shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean it in water. Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic Wet/Dry shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method. Charge the shaver for at least 8 hours before using it for the first time or when it has not been in use for more than six months. Parts identification (see fig. 1) @ Protective cap © System outer foil © System outer foil release buttons © Foil frame © Inner blades © Foil frame release buttons © Switch lock button © On/Off switch © Recharge lamp/Charge status lamp © Trimmer © Trimmer handle © Charging adaptor holder © Charging adaptor with automatic voltage adjustment © Rotatable stand © Cleaning brush © Wall mount © Travel pouch How to use the wall mount The charging adaptor can be hung on the wall using wood screws. 1. Lift up the charging adaptor holder. (see fig. 1 (A)) 2. Select an appropriate location on the wall where the screws can go in. 3. Attach the wall mount to the wall as shown with the wood screws, making sure that the arrow points up. 4. Slide the charging adaptor grooves into the wall mount until it clicks in. (see fig. 1 (B)) To remove the charging adaptor from the wall mount, slide the adaptor upward. Charging adaptor (see fig. 1) Lift the charging adaptor holder until it clicks in when charging the shaver, (see fig. 1(A)) (Restore the charging adaptor holder when carrying the unit.) (see fig. 1(C)) Rotate the stand on the bottom of the charging adaptor when you need extra stability. (see fig. 1(D)) Charging (see fig. 2) Place the charging adaptor upright on a flat surface or mount it on a wall. Plug the adaptor into an AC outlet. It will adjust automatically to voltages 0S01G108_ES7016_EUR_en 1/28/02, 9:29 AM 5 5 xhui I 4 I between 100-240V AC. In some areas, a special plug adaptor may be required. Switch the shaver to the “0 • charge” position and place it upright into the charging adaptor with the switch facing toward the front. The charge status lamp will glow red when the shaver is placed on the correct position. It will flicker red when the charging is completed (see fig. 2 (A)). You can fully charge the shaver in one hour if the recharge lamp flashes green (see fig. 2 (B)). A full charge will supply enough power for about 20 shaves (three minutes per shave for a normal beard). You can always store your shaver in the charging adaptor to maintain full power capacity. This shaver cannot be overcharged. Before traveling, charge it fully for 1 hour if you will not be taking the charging adaptor with you. Using your shaver Depress the switch lock button and slide the On/Off switch upward to turn the shaver on. Hold the shaver at a right angle (90°) to your skin (see fig. 3). Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. System outer foil (see fig. 4) System outer foil has a slit blade (a) between two foils (b). They move up and down independently to follow the contours of your face. The slit blade catches and cuts longer and lying hairs easily. For wet shaving Put a thin layer of shaving foam on your face which works as a lubricant. Shaving foam is the most suitable among many other shaving aids (gel, soap, cream, etc). Do not put a thick layer of shaving foam as it may affect the shaver's performance. If the shaving head is clogged with foam, simply rinse it under running water. Using the trimmer (see fig. 5) Slide the trimmer handle up to the mm position until it clicks in. Place the trimmer at a right angle to your skin and move it downward to trim sideburns. Cleaning your shaver (see fig. 6) For cleanliness and convenience, we recommend that you clean your shaver with water and a liquid hand soap. Regular cleaning will keep your shaver in good condition while preventing odors or bacteria from developing, and maintain the cutting performance. With the system outer foil in place, apply some hand soap onto the outer foil. 0S01G108_ES7016_EUR_en 1/28...
Ce manuel est également adapté pour les modèles :Outils cosmétiques - ES7016 (665.22 kb)