Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
15). 2. Was the detergent cartridge detached during cleaning? > Reset the detergent cartridge. After completing inspection and treatment • Properly set the detergent cartridge to extinguish the status lamp and start each course. In cases when the status lamp is illuminated, detach the shaver from the self-cleaning recharger and carry out the following inspections. • Note that there are cases where the blade will be hot or wet if cleaning is not completed. • Check to ensure that the clean lamp has been extinguished. 1. Is the water tank and its cap set properly? > Attach the water tank and its cap properly. 2. Is the self-cleaning recharger tilted? > Place the self-cleaning recharger on a horizontal surface. 13 When an abnormality has corrected in accordance above two inspections. • Hold down the select button for approximately two seconds to extinguish the status lamp each course. When no abnormality was found after the above two inspections. • It is time to replace the detergent cartridge and cleaning liquid inside the water tank. (The same cartridge has been used to clean approximately 30 ~ 40 days worth of beard shavings.) > Drain the old cleaning liquid inside the water tank and refill the tank with water. Additionally, replace the old detergent cartridge with a new one. • If the status lamp blinks or illuminates again even after the inspections and treatments above have been carried out, contact an authorized service center. 2 Cleaning your shaver withoutthe self-cleaning recharger (see fig. 19) Warning – To prevent electric shock or personal injury, turn the shaver off and disconnect the power cord from the shaver before cleaning with water. With the system outer foil in place, apply some hand soap onto the outer foil. Push the On/Off switch more than 2 seconds to activate the turbo mode for “ sonic” vibration cleaning. At the same the “ sonic” clean- outer foil will become ing symbol appears during use, or shaving capabilities display. will be deteriorated. Pour some water over the outer foil. Replacing the inner After about 20 seconds, it will be (see fig. 21) automatically turned off, or you can Squeeze the system outer foil re turn it off by pushing the On/Off lease buttons and lift the system switch. outer foil upward to remove it. Re- Remove the system outer foil and move the inner blade one at a time push the On/Off switch more than 2 by grasping it firmly at both ends and seconds to activate the turbo mode pulling straight away from the shaver. for “ sonic” vibration cleaning and Do not touch the metal parts of inner clean it with running water. blades. Wipe off any moisture from the To insert the new inner blade, hold shaver with a dry cloth and dry it with- the blade one at a time at both ends out the system outer foil. and press downward until it snaps It is recommended to clean your into the shaver. shaver with the self-cleaning recharger or the “ sonic” vibration ATTENTION: cleaning when the tap symbol (a) A Lithium-ion battery that is recyappears in LCD. clable powers the product you have purchased. Please call 1Replacing shaving head 800-8-BATTERY for information on components how to recycle the battery. It is recommended that you replace the system outer foil at least once a year and the inner blade at least once every 2 years to maintain your shaver’s cutting performance. Replacing the system outer foil (see fig. 20) WARNING for Lithium Battery: Squeeze the system outer foil re- Fire, explosion, and severe burn lease buttons and lift the system hazard. outer foil upward to remove it. To in- Do not crush, disassemble, heat sert the new system outer foil, press above 100° C (212° F), or incinerate. down until it snaps into place. • Check that the gaps on both sides How to remove the built-in of the system outer foil release rechargeable battery before buttons and the system outer foil disposal of the shaver are equal. If they are not equal, (see fig. 22) there is a chance that the system 14 • Keep the adaptor from water WARNING – Do not attempt and handle it hands. place the battery for the purpose • Grip the adaptor when of reusing the shaver. This could ing it from an AC outlet; tugging on result in the risk of fire or electric the power cord may damage it. shock. • Do not pull, twist, or severely bend the power cord. The battery in this shaver is not in • Do not wrap the power cord tightly tended to be replaced by consum around the appliance. ers. However, the battery may be re • If the power cord gets damaged, it placed at an authorized service alone cannot be replaced. Contact center. The procedure described be an authorized service center. low is intended only for removal of • Store the adaptor in a dry area the rechargeable battery for the pur where it will be protected from dam- pose of proper disposal. 1. Disconnect the power cord from age. • The shaver and adaptor will be- the shaver when removing the come slightly hot during use or battery. charging, however this is not a 2. ...