Évaluations - 3, GPA: 4
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
• ChargeCharging using the self.cleaning rechargerThoroughly wipe off any drops of water on or around the self.cleaning recharger so that it is dry before charging the shaver. 11Insert the appliance plug into the self.cleaning recharger. 22Remove the protective cap and then gently insert the shaver as shown. 33Plug in the AC adaptor into a household outlet. 132The “Charge” course starts when attaching the shaver. Turn the shaver off before inserting. Check that the outer foil is not deformed or damaged when you insert the shaver. Wipe off any water droplets on the main body rear terminal. You can charge even with the STATUS lamp of the self.cleaning recharger is blinking. Charging is completed after approx. 1 hour. If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration. You can keep the shaver attached to the self.cleaning recharger, or connected to the AC adaptor, when not using it to maintain full battery capacity. You cannot overcharge the shaver. • • • • • • • Charging without the self.cleaning rechargerYou can also charge without the self.cleaning recharger. 11Insert the appliance plug into the shaver. 22Plug in the AC adaptor into a household outlet. 12You cannot operate the shaver while charging. Reading the LCD panel when chargingThe LCD panel shows the remaining battery capacity from 0% to 100%, in 10% increments. While charging After charging is completed The indicators glow. Battery capacity and Charge status will light up and then turn off after 5 seconds. After charging is completed, turning the power switch ON with the shaver plugged in will cause Battery capacity and Charge status to light up and then turn off after 5 seconds. This shows that the shaver is fully charged. • English Recommended ambient temperature for charging is 5.35 °C (41- 95 °F). The battery may not charge properly or not at all under extreme low or high temperatures. The indicators on the LCD panel blink when there is a problem with charging. When charging the shaver for the first time or when it has not been in use for more than 6 months, the indicators on the LCD panel may not glow. It will eventually glow if kept connected. Shave Using the shaver 1 Rotate the lock ring to unlock the power switch and press the power switch. Page 5 2 Hold the shaver as illustrated above and shave. We recommend using the shaver in an ambient temperature range of 5 - 35 °C (41 - 95 °F). If used outside this range, the appliance may stop operating. Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. • • • Caution If you press the power switch for more than 2 seconds, the sonic vibration cleaning mode is activated. Page 11 You cannot shave in this mode. Do not place your fingers on the power switch while using the shaver. This may cause the shaver to turn off or enter the sonic vibration cleaning mode. Place your thumb on the thumb rest while using the shaver. • • Using the trimmer You can change the pivot action. Slide the handle up to “ ” when using the trimmer. FREE You can move the shaver head. LOCK You can lock the shaver head. Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns. English Reading the LCD panel when using During use After use 5 seconds. shown alternately after turning The used time is shown. The indicators turn off after• The used time and the remaining battery capacity are • The shown time returns to off the shaver. [0’00”] after 10 minutes. When the battery capacity is low You can shave 1 to times after “10%” appears. (This will differ depending on usage.) • “10%” appears and blinks. • A full charge will supply enough power for approx. 14 shaves of 3 minutes each. (This will differ depending on usage.) Clean Cleaning using the self.cleaning recharger .Preparing the self.cleaning recharger Remove the shaver and the appliance plug from the self.cleaning recharger. 1 11 Remove the water tank and then open the water tank cap. 2 22 Wash away the old cleaning liquid and then rinse the water tank. 3 33 Pour tap water into the water tank. • Do not let the water rise above the maximum water line. This may cause the cleaning liquid to spill. 4 44 Securely close the water tank cap and then attach the tank. 5 55 Peel off the 2 seals from the new detergent cartridge. • Hold the detergent cartridge horizontally. (The detergent may spill if the detergent cartridge is tilted too much.) . . Precautions for the detergent cartridge • Keep out of reach of children. • Only use to clean the blades of electric shavers. • Carry out emergency measures if the Cleaning agent enters mouth or eyes, and consult a doctor. 6 66 Attach the detergent cartridge. • Replace the de...