Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
In this case, the charge status lamp blinks twice in 1 second. 6 The charge status lamp will glow when the shaver is being charged. The battery capacity monitor will all illuminate and the charge status lamp will blink after charging is completed (see fig. 3 (A)). 10 minutes after charging is completed, the battery capacity monitor will extinguish and these charge status lamp will continue to blink (see fig. 3 (B)). You can fully charge the shaver in 1 hour if the LED display shows “low” (low). The battery capacity monitor indicates the charge remaining in the battery in 3 levels (high/mid/low). The unit can be used once or twice more after “low” (low) starts to blink. (Differs depending on the use situation.) A full charge will supply enough power for approx. 14 shaves (3 minutes per shave for a normal beard). You can always connect yourshaver to the adaptor to maintain full battery capacity. This shaver cannot be overcharged. Before travelling, charge it fully for 1 hour if you will not be taking the adaptor with you. In case your shaver is without charge, you may quick charge it for 1 shave in about 5 minutes. Disconnect the power cord from the shaver, and push the On/Off switch to turn the shaver on. If you push and hold the On/Off switch for more than 2 seconds, it will activate the turbo mode for “sonic” vibration cleaning. (see “Cleaning your shaver”) Caution: Shaving with “sonic” vibration may damage your skin. Please turn it off and on again to deactivate the turbo mode. Do not place fingers on the On/Off switch during use. This may cause the shaver to stop during use or change it to the “sonic” vibration cleaning mode. Hold the shaver at a right angle (90°) to your skin (see fig. 4). Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. System outer foil (see fig. 5) System outer foil has a slit blade (a) between 2 foils (b). They move up and down independently to follow the contours of your face. The slit blade catches and cuts longer and lying hairs easily. Using your shaver Caution - The system outer foil is very thin and can be damaged if handled improperly. Before each use, always check the foil for damage. To avoid personal injury, do not use if the foil or other parts of the shaving head are damaged. 7 P006-123_ES8807_EU 06.8.9 13:11 ^->'8 For wet shaving Put a thin layer of shaving foam on your face which works as a lubricant. Shaving foam is the most suitable among many other shaving aids (gel, soap, cream, etc.). Do not put a thick layer of shaving foam as it may affect shaver's performance. If the shaving head is clogged with foam, simply rinse it under running water. Using the trimmer (see fig. 6) Slide the trimmer handle up to open the trimmer. Place the trimmer at a right angle to your skin and move it downward to trim sideburns. Cleaning your shaver (see fig. 7) Warning - To prevent electric shock or personal injury, disconnect the power cord from the shaver before cleaning with water. Forcleanliness and convenience, we recommend that you clean your shaver with water and a liquid hand soap. Regularcleaning will keep your shaver in good condition while preventing odors or bacteria from developing, and maintain the cutting performance. With the system outer foil in place, apply some hand soap onto the outer foil. Push and hold the On/Off switch for more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning. At the same time, the lamps of the Battery capacity monitor illuminate randomly. Pour some water over the outer foil. After about 20 seconds, it will be automatically turned off, or you can turn it off by pushing the On/Off switch. Remove the system outer foil and push the On/Off switch more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning and clean it with running water. Wipe off any moisture from the shaver with a dry cloth and dry it without the system outer foil. Lubrication (see fig. 13) To maintain shaving comfort for a long time, it is recommended that the oil provided with the shaver is used. 1. Switch off the shaver. 2. Apply one drop of oil to each of the outer foils. 3. Raise the trimmer and apply a drop of oil. 4. Switch the shaver on, and run it for approximately five seconds. 5. Switch off the shaver, and wipe off any excess oil from the outer foils with a soft cloth. Brush cleaning Squeeze the foil frame release buttons and lift the foil frame upward to remove it (see fig. 9). Remove the inner blades one at a time by grasping it firmly at both ends and pulling it straight away from the shaver. Clean the outer foils, the shaver body and the trimmer with the long brush (see fig. 10). Clean the inner blades with t...
Ce manuel est également adapté pour les modèles :Autres appareils personnels - ES8807 (1.58 mb)