Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
ER217 Before operating this unit, please read these instructions completely. POOO-005(ER217Ш'Н) 06.01.26 11:01 ^->'2 2 POOO-005(ER217Ш'Н) 06.01.26 11:01 ^->4 4 Index ENGLISH Page 6 DEUTSCH Seite 12 FRANÇAIS Page 19 ITALIANO Pagina 26 NEDERLANDS Pagina 32 ESPAÑOL Pagina 39 DANSK Side 46 PORTUGÊS Pagina 52 NORSK Side 59 SVENSKA Sid 65 SUOMI S i vu 71 TÜRKÇE Sayfa 77 POLSKI Strona 83 CESKY Strona 90 MAGYAR Oldal 96 ROMANA Pagina 103 pycckmi/i CîpaHML(a 110 YKpaÏHCbKa CfopiHKa 117 5 P006-018(ER217№)'N) 06.01.26 11:02 ^->’6 This Beard/Hair Trimmer is for the trimming and care of mustaches, beards and hair. Trimming length can be adjusted between 1 to 20 mm.The trimmer can be operated either from an AC power source or on its own rechargeable battery. Parts identification (see fig. 1) ® Switch Slide up to turn on, slide down to turn off. ® Charge Indicator Lamp Lights when the unit is connected with the adaptor @ to an AC power source for charging. © Main Blade A precision 39 mm-wide blade which can be used with the comb attachment ©. d Quick Adjust Dial Turn the dial to a higher setting to raise or lower the comb attachment © to the desired length (between 1 and 20 mm) (see fig. 2). The comb attachment is locked in position when the switch is set to “1”. (D Trimming Length Indicator Indicator Trimming Length 1 1.0 mm 2 2.0 mm • 3.5 mm 5 5.0 mm • 6.5 mm 8 8.0 mm • 9.5 mm 11 11.0 mm • 12.5 mm 14 14.0 mm • 15.5 mm 17 17.0 mm • 18.5 mm 20 20.0 mm • The actual hair length may be longer than the set trimming length. © Comb Attachment Use this to control the trimming length, (see fig. 3) © Moving Blade ® Stationary Blade ® Cleaning Lever Push this lever to remove bits of hair caught between the stationary blade and the moving blade. © Blade Block Release to remove the blade block from the housing to clean or replace the blade, (see fig. 12) ® Thinning Plate When thinning, slide the thinning plate up until it firmly clicks in position, (see fig. 7) l Thinning Plate Lock Button Press and hold while sliding the Thinning plate down to set the Thinning Plate back to its original position. © Adaptor Use this to connect the trimmer to an AC power source for recharging or for AC operation. ® Oil Lubricate the space between the stationary and moving blade with 2 or 3 drops of oil after use. (see fig. 16) © Cleaning Brush READ ALL INSTRUCTIONS BEFORE USE. Operation Charging and cordless trimming When charging the beard/hair trimmer for the first time or when it has not been in use for more than 6 months, charge it for the activation for at least 16 hours before use. Connect the power cord to the beard/ hair trimmer, and plug the adaptor to an AC outlet. In some areas, a special plug adaptor may be required. The charge indicator lamp will glow red and it will stay on until the adaptor is disconnected from the AC outlet. (see fig. 4) You can fully charge the trimmer in 8 hours if it seems to be losing speed. A full charge will supply enough power for approx. 10 trims (5 minutes per trim for a normal beard). AC operation Connect the AC adaptor to the body in the same way as for charging, and set the switch to “1” to use the trimmer. If the trimmer does not operate after connection as mentioned above, return switch to “Ocharge” position for 1 minute and then set switch back to “1” position. Trimming of beard Place the angled face of the comb against the skin and cut the beard by moving the trimmer in all directions to obtain a uniform cut. (see fig. 5) With curly facial hair, the comb attachment may not cut all of the hair. In this case, remove the comb attachment and use a conventional comb to draw out the remaining uncut, hair, (see fig. 6) When shaping the beard, remove the comb attachment. Place the angled edge against the skin and make the border of the beard even. 7 P006-018(ER217№)'I'I) 06.01.26 11:02 /4-V8 How to use the thinning function (see fig. 9) First, slide the Thinning plate up to “1/3” until it clicks, (see fig. 7) While applying the blade point at right angles to the hair, run the trimmer slowly across the head as if combing the hair. After thinning, slide the thinning plate back while pushing the Thinning Plate Lock Button, (see fig. 8) Notes on thinning For thinning, confirm that the thinning plate is set to the right position. Incorrect setting may result in excessive cutting. If a difference in level is produced, lightly thin to compensate. If thick and thin portions are produced, or if there are portions with an excessive amount of hair, thin the appropriate portions to compensate. Point: Thin the hair gradually while checking the overall balance. Cutting of hair Cut hair to the correct height by moving the trimmer back against the flow of the hair. Cutting around the ears Cut a little, and then gently separate the trimmer from the hair (see fig. 10). Cutting the nape of the neck Bring the trimmer gently away ...
Ce manuel est également adapté pour les modèles :électrique - ER217 (3.83 mb)