|
Facilité d'utilisation
While travelling, do not take an unsealed cartridge along nor leave one in the shaver. Shaving GlideControl allows you to choose the amount of Shaving Conditioner you want to apply («min»/«max»): When you raise the distancing bar (moving the scale to «min»), the applicator will have less contact with your skin and will apply less Shaving Conditioner. If you move the scale to «max», more Conditioner will be applied. Please be aware that, in order to optimally pre-condition your skin, during the first seconds somewhat more Conditioner will be applied. Before shaving you should not use moisturizing creme or lotions, as they might impair the effectiveness of the applicator. No need to restrict the use of After Shave or Eau de Toilette. Turning on the shaver («start»): The pivoting cutting system automatically adjusts to every contour of your face. 6 Head lock: Shaving in difficult areas (e.g. under the nose) will be facilitated if the shaving head is locked. Trimmer: When the long hair trimmer is activated, it allows the controlled trimming of moustache or sideburns. Tips for the perfect shave • How much Shaving Conditioner you want to apply depends on your type of skin: wet skin might require more Shaving Conditioner. You may want to try out different scale positions. • Hold the shaver at right angles (90°) to the skin. Stretch your skin and shave against the direction of beard growth. • To maintain 100% shaving performance, replace your foil and cutter block at least every 18 months or when worn. Keeping your shaver in top shape This appliance is suitable for cleaning under an open water tap. Warning: Detach the hand-held part from the power supply before cleaning it in water. Important: When the foil frame is removed, do not turn on the shaver. Shaving Conditioner would leak. Daily cleaning After each shave, you should hold the shaver - turned on and with its foil frame attached - upside down under running hot water. General cleaning Occasionally you should, while the shaver is turned off, remove the foil frame, and, using the brush, clean the cutter block and the inner area of the shaver head. Replace foil frame, ensuring both sides click audibly into place. If not properly attached, Shaving Conditioner could leak. 7 Note When cleaning under running water, water may condensate inside the shaver‘s cartridge chamber. This has no effect on the shaver‘s operation and will disappear after a while. Changing the applicator The applicator is subject to wear. You should exchange it when in the course of time you feel that less Shaving Conditioner is applied. Replacement applicators come with Shaving Conditioner refill cartridges (see «Accessories»). a) Remove the foil frame. b) Lift old applicator at the notch on one side, then the other. c) Remove old applicator and dispose. d) Place new applicator on the foil frame, leaving a small gap. e) With both thumbs push applicator right and left until it clicks into place. f) Replace foil frame, ensuring both sides click audibly into place. Replacing the shaving parts To maintain 100% shaving performance, replace your foil and cutter block at least every 18 months or when worn. Change both parts at the same time for a closer shave with less skin irritation. (Foil frame and cutter block: FreeGlider) Accessories Available at your dealer or Braun Service Centres: • Foil frame and cutter block (FreeGlider) • Cartridge with Shaving Conditioner (SCR) 8 Environmental notice This product contains rechargeable batteries. In the interest of protecting the environment, please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at a Braun Service Centre or at appropriate collection points provided in your country. The empty cartridge of the Shaving Conditioner can be disposed in the household waste. Subject to change without notice. This product conforms to the European Directives EMC 89/336/EEC and Low Voltage 73/23/EEC. For electric specifications, see printing on the special power supply cord set. 9 What to do if. Problem Situation Solution Shaving Conditioner is leaking Foil frame replaced incorrectly or Applicator replaced incorrectly or Shaver was switched on with foil frame removed or Cartridge was removed immediately after use Remove foil frame and attach once more, ensuring both sides click audibly into place. If needed, clean both foil frame and shaver head. Place new applicator on the foil frame, leaving a small gap. With both thumbs push applicator right and left until it clicks into place. Do not switch on when foil frame is removed. Do not remove cartridge immediately af...
Ce manuel est également adapté pour les modèles :électrique - 6620 (6.1 mb)
électrique - 6640 (6.1 mb)