Évaluations - 0, GPA: 0 ( )

Fabricant : Philips Taille : 4.07 mb Nom Fichier : Langue d'enseignement:

RQ1285:The display starts to count down from 3. , At 1, the appliance beeps to indicate that it is locked. The lock symbol lights up on the display. After a few , seconds it goes out. Deactivating the travel lock 1 Press the on/off button for 3 seconds. The motor starts running to indicate that the travel lock , has been deactivated. The shaver is now ready for use again. Note:When you place the shaver in the plugged-in charger or Jet Clean System, the travel lock is automatically deactivated. english 45 Blocked shaving heads Note:The displays of the various shaver types look different, but show the same symbol. -If the shaving heads are blocked, the shaving unit symbol, the tap symbol and the exclamation mark flash. In this case, the motor cannot run because the shaving heads are soiled or damaged. -When this happens, you have to clean the shaving unit or replace it. -The shaving unit symbol, the tap symbol and the exclamation mark continue to flash until you unblock the shaving heads. charging Charging takes approx. 1 hour. RQ1285/RQ1275/RQ1260: A fully charged shaver has a shaving time of up to 60 minutes or 20 days. Note: RQ1285/1275/1260:When the battery is fully charged, the display shows the actual remaining shaving minutes (see section ‘Battery fully charged’ in chapter ‘The display’). RQ1250: A fully charged shaver has a shaving time of up to 50 minutes or 16 days. Charge the shaver before you use it for the first time and when the display indicates that the batter y is almost empty (see section ‘Batter y low’ in chapter ‘The display’). Quick charge After the shaver has charged for 5 minutes, it contains enough energy for one shave. charging in the charger 1 Insert the small plug into the charger. 46 english 2 Unfold the charger (‘click’). 3 Put the adapter in the wall socket. 4 Put the shaver in the charger. The display shows that the shaver is charging (see , chapter ‘The display’). charging in the Jet clean system (RQ1285, RQ1260/21, RQ1250/21 only) 1 Put the small plug in the Jet Clean System. 2 Put the adapter in the wall socket. 3 Hold the shaver upside down above the holder with the back of the shaver pointing towards the holder. Note:The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit. 4 Place the shaver body in the holder behind the two clips (1) and press it down until it locks into place (2). The display shows that the shaver is charging (see , section ‘Charging’ in chapter ‘The display’). - , - , english 47 using the shaver shaving skin adaptation period Your first shaves may not bring you the result you expect and your skin may even become slightly irritated. This is normal. Your skin and beard need time to adapt to any new shaving system. We advise you to shave regularly (at least 3 times a week) for a period of 3 weeks to allow your skin to adapt to the new shaver. During this period, use your new electric shaver exclusively and do not use other shaving methods. If you use different shaving methods, it is more difficult for your skin to adapt to the new shaving system. 1 Press the on/off button once to switch on the shaver. The display lights up for a few seconds. , 2 Move the shaving heads over your skin in circular movements. Do not make straight movements. 3 Press the on/off button once to switch off the shaver. The display lights up for a few seconds and then shows the remaining battery capacity. Wet shaving You can also use this shaver on a wet face with shaving foam or shaving gel. To shave with shaving foam or shaving gel, follow the steps below: 1 Apply some water to your skin. 2 Apply shaving foam or shaving gel to your skin. 3 Rinse the shaving unit under the tap to ensure that theshaving unit glides smoothly over your skin. 4 Press the on/off button once to switch on the shaver. 5 Move the shaving heads over your skin in circular movements. Note: Rinse the shaver under the tap regularly to ensure that it continues to glide smoothly over your skin. 48 english 6 Dry your face and thoroughly clean the shaver after use (see chapter ‘Cleaning and maintenance’). Note: Make sure you rinse all foam or shaving gel off the shaver. using the trimmer You can use the trimmer to groom your sideburns and moustache. 1 Pull the shaving unit straight off the shaver. Note: Do not twist the shaving unit while you pull it off the shaver. 2 Press the on/off button once to switch on the shaver. The display lights up for a few seconds. , 3 Slide the trimmer slide forwards to slide out the trimmer. 4 You can now start trimming. 5 Slide the trimmer slide backwards to retract the trimmer. 6 Press the on/off button once to switch off the shaver. The display lights up for a few seconds and shows the , remaining battery capacity. 7 Insert the lug of the shaving unit into the slot in the top of the shaver (1).Then press down the shaving unit (2) to attach it to the shaver (‘click’). english 49 using the Beard styler attachment (RQ1285/RQ1275 only) Note: Onl...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :