Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Only use the HQ8000/ 600 powerplug supplied to charge the shaver. . The powerplug transforms 100-240 volts to 12 volts. C . Make sure the HQ8000/ 600 powerplug does not get wet. C . The shaver runs at a safe low voltage of 12 volts. It is watertight and can be cleaned under the tap. Do not rinse with water hotter than 80cC. . For the best shaving results, shaving emulsion should be pumped up frequently. Charge indications C . As soon as you start charging the empty shaver, the green pilot light will go on. . When the batteries are running low, the pilot light turns red. . The pilot light will blink red for a few seconds after the shaver has been switched off. Charging Recharge and keep the appliance at a temperature between 5cC and 35cC. The powerplug is suitable for mains voltages ranging from 100 to 240V. . You cannot use the shaver when it is charging, because the appliance does not work while its batteries are being charged. ENGLISH C 1 2 Put the appliance plug in the shaver. Put the powerplug in the wall socket. Do not recharge the shaver in a closed pouch or cassette. 3 When charging for the first time or after a long period of disuse: leave the shaver to charge continuously for 12 hours. Charging normally takes approx. 8 hours. A fully charged shaver has a cordless shaving time of up to 25 minutes. 4 To extend the lifetime of the batteries, remove the powerplug from the wall socket and pull the appliance plug out of the shaver when the batteries have been fully charged. The shaver does not work if it is connected to the mains. Inserting cartridges The car tridges with moisturising NIVEA FOR MEN shaving emulsion are available in boxes containing five car tridges and one small plastic pump. Do not throw the pump away: you will need it for all five car tridges! Use only Philishave NIVEA FOR MEN Cool Skin (HQ160 or HQ161) car tridges. ENGLISH For hygienic reasons, we advise you to inser t a new pump when you star t using a new set of five car tridges. Inserting the first cartridge 1 2 1 Take one cartridge from the box.Take the pump (supplied in the same box) out of its bag and push it into the cartridge until it locks into position with a click. C 2 Move the release slide downwards and open the cover of the cartridge compartment. C C 3 Slide the cartridge with the pump into the shaver. It only fits properly if the white side of the pump is pointing downwards. Close the cover. 4 Press the yellow pump button a few times until the NIVEA FOR MEN shaving emulsion appears.The shaver is now ready for use. Do not throw the pump away when you replace an empty car tridge.You will need it for the other car tridges. ENGLISH C C The NIVEA FOR MEN shaving emulsion in this car tridge will keep when stored at temperatures between 0cC and +40cC. Shaving 1 2 Switch the shaver on by pressing the on/off button once. Press the yellow pump button to apply NIVEA FOR MEN shaving emulsion to your skin. Move the shaver over your skin, making both straight and circular movements. 3 While shaving, press the pump button frequently to apply more NIVEA FOR MEN shaving emulsion so that the shaver keeps gliding smoothly over your face. Do not press the shaver too hard against your skin while shaving. If you prefer, you can wet your face first. . When you have run out of shaving emulsion, you can also use the shaver without it on a dry face. . Your skin may need 2 or 3 weeks to get accustomed to the Philishave system. 4 5 Switch the shaver off. Put the protection cap on the shaver to prevent damage. 8 ENGLISH C C C 3 Remove the car tridge and clean the shaver if you are not going to use the appliance for more than one week. Rinse the shaver after each shave. Trimming The shaver has a separate trimmer for grooming sideburns and moustache. 1 Switch the shaver off. Clean the shaver before you attach the trimmer. 2 3 4 Press the release button and pull the shaving unit off the shaver. Tilt the trimmer slightly backwards and fit it onto the shaver. Remove the trimmer by pressing the release button again. Cleaning Shaving unit Rinse the shaving unit and the hair chamber with hot water (60cC - 80cC) after ever y use. Switch the shaver off. Press the release button and flip the shaving unit open. 1 2 ENGLISH 3 Clean the shaving unit and the hair chamber by rinsing them under a hot tap for some time. C Never dr y the shaving unit with a towel or tissue as this may damage the shaving heads. 4 Rinse the outside of the appliance. C Make sure the inside of the shaving unit and the hair chamber have been cleaned properly. Close the shaving unit and shake off excess water. . If the shaving unit becomes detached from the shaver accidentally, reattach it by pushing the hooks into the holes on the rear side of the appliance. 5 Leave the shaving unit open to let the appliance dry completely. Trimmer 1 2 Clean the outside of the trimmer with the brush supplied after every use. Flip the trimmer open to clean it on the inside. C 10 ENGLISH 3 C C C C C 3 Lubri...