Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
2 Do not leave the appliance in a position where it can become damaged by direct sunlight or other heat source. - Before first use or - if the shaver has not been used for a month or longer it should be charged for a period of at least 8 hours (irrespective of the reading on the display). If the batteries are completely empty, it may take some time (3-5 minutes) before information appears in the display. • Please bear in mind that your skin may need two to four weeks to become fully accustomed to the Philishave shaving system. 885 885 1 2 Important English To protect the environment, this rechargeable Philishave appliance is equipped with nickel-hydride batteries. These contain less than 0.01% cadmium. Yet we advise you to ensure that the batteries are separated from the normal household refuse and that they are disposed of at an officially assigned place when discarding your appliance in due course. Please refer to section “Protecting the environment”. Switching on/off 3 The slider switch has a locking knob which prevents the shaver from being switched on accidentally. Keeping the small knob on the switch pressed-in slide the switch upwards/downwards. Charging • Ensure that the shaver is switched off. • It is advisable to charge the shaver at temperatures between 5° and 35° C (41° and 95° F). This guarantees maximum life from the rechargeable batteries. • If you keep the shaver in the case when charging ensure that the lid is left open to prevent overheating. • Before first use (or if the shaver has not been used for a long time) it should be charged for a period of at least 8 hours. 4 • Recharging: 60 minutes. The shaver can also be charged from a 12 - 24 Volts (DC) supply using cord connector type HP 1957. (Available from Philips retailers or Authorised Service Dealers.) Charging from a 12 -24 Volts (DC) supply requires approx. 24 hours. • Regular cleaning of the shaver means that less battery energy is consumed, so that more shaving time becomes available. • The shaver will not be damaged by leaving it connected to the mains supply after it is fully charged. However, it is not advisable to charge the shaver permanently as this would shorten the life of the rechargeable batteries. 4 Insert the small plug into the shaver. Ensure that the plug is pushed fully home. (Note the indication mark.) Mains voltages: 100 - 240 Volts. (The shaver adjusts automatically.) 890 4 5 The green pilot light comes on. If the batteries are almost empty, the red pilot light will come on as well. When this light goes out, there is enough energy in the rechargeable batteries for one cordless shave (3 minutes). 6 After 60 minutes the green pilot light starts to flash. This means that the shaver is fully charged. 890 890 5 890 890 Cordless shaving 7 When the red pilot light comes on, the reserve energy has been reached. (You will be able to complete the shave.) As the shaver is switched off the red pilot light will start flashing and you will hear a sound signal for 4 seconds. This indicates that it is time to recharge the shaver. Have you missed out charging? When the batteries are completely empty and the shaver stops, you can give the shaver a quick charge (sufficient for one cordless shave): -Charge the shaver until the red pilot light goes out. Shaving directly from the mains supply (wall socket) -If you wish you can connect the shaver to a wall socket using the mains cord and shave directly from the mains supply. 6 Shaving 98 8 Switch on. 9 Move the shaving unit quickly over the skin and especially against the direction of the hair growth, stretching the skin with your free hand to bring the hairs into an upright position. • Best results are obtained if the skin is dry. Preferably shave before or some time after washing. • If required apply a pre-shave lotion. This can be particularly helpful if the climate is warm and humid. 7 Trimmer The trimmer can be engaged whilst the motor is running. 1110 12 OIL 10 To engage the trimmer push the slide upwards. To disengage move the slide downwards. Brush the trimmer clean after each use. 11 The trimmer has been especially designed for grooming sideburns, moustache and beard. The trimmer is not required for long hairs in the neck area; these hairs can easily be shaved off with the shaving unit. 12 Maintenance (every six months) Apply two drops of light machine oil to the teeth of the trimmer. 8 Cleaning • Always ensure that the mains cord is disconnected and the shaver is switched off before carrying out maintenance or cleaning. • Handle the shaving heads carefully to avoid causing damage. • Advice: Clean the shaver regularly. 13-16 Every week: shaving head slots and hair chamber - (Fig. 13) Use the short bristled brush to clean the shaving head slots. - (Fig. 14) To remove the shaving unit depress the retaining button (1) and lift the shaving unit from the shaver (2). - (Fig. 15/16) Remove hairs from the chamber and shaving unit using the long bristled brush. 9 13 15 16 14 1 ...