Log:
Évaluations - 4, GPA: 4.3 ( )

Instructions Generac, Modèle 02010-1

Fabricant : Generac
Taille : 9.56 mb
Nom Fichier : 1f9b9e27-cd91-4654-a005-0176e7efd304.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Close windows, doors and other openings in the vehicle that, if open, might permit exhaust gases to enter the vehicle. —A ESE13 A— A The generator engine gives off DEADLY carbon monoxide gas through its exhaust system. This dangerous gas, if breathed in sufficient concentrations, can cause unconsciousness or even death. Never operate the generator set with the vehicle inside any garage or other enclosed area. DO NOT OPERATE THE GENERATOR IF THE EXHAUST SYSTEM IS LEAKING OR HAS BEEN DAMAGED. SYMPTOMS OF CARBON MONOXIDE POISONING ARE (a) inability to think coherently; (b) vomiting; (c) twitching muscles; (d) throbbing temples; (e) dizziness; (f) headaches; (g) weakness; and (h) sleepiness. IF YOU FEEL ANY OF THESE SYMPTOMS, MOVE INTO FRESH AIR IMMEDIATELY. IF SYMPTOMS PERSIST, GET MEDICAL HELP. 2.5 STARTING THE GENERATOR NOTE: Read the vehicle manufacturer’s instructions. The owner/operator should become familiar with the vehicle in which this generator is installed. Differences exist between vehicles. For example, some vehicles may use a transfer switch to isolate dockside power from the generator, while other vehicles may use an isolating receptacle. Some vehicles may be equipped with a DC converter, which allows the generator to power certain DC lighting and other DC loads. 8 Generac* Power Systems, Inc. Section 2 - Operation PRIMEPACT 50 Recreational Vehicle Generator OPERATION To start the generator from either the generator control panel or from the optional remote panel, proceed as follows: 1. Turn OFF electrical loads using the means provided in your vehicle (such as a main line circuit breaker or transfer switch). NOTE: If starting from the generator control panel, turn OFF loads by setting the generator’s main circuit breaker to the OFF (or open) position. If starting from a remote panel, turn OFF loads using the means provided in the vehicle (such as a main circuit breaker). Electrical load circuits will be turned ON after the generator has started, stabilized and warmed up. 2. If you have not started the engine in more than two weeks, press the Fuel Pump Primer switch and hold it for about 10 to 15 seconds to prime the fuel system. However, if the engine is warm, skip Step 2. 3. Hold the engine Start/Stop switch in the START position to crank the engine. Release the switch when the engine starts. -A CAUTION A- A If the engine does not start after it has been cranking for 15 seconds, release the Start/Stop switch and try again. Holding the switch for longer than 15 seconds can damage the starter motor. 4. Let the engine run at no-load for a few minutes to stabilize and warm up. 5. Turn ON electrical loads using the means provided (such as a main circuit breaker or transfer switch). 2.6 STOPPING THE GENERATOR 1. Turn OFF all electrical loads using the means provided (such as a main circuit breaker or transfer switch). 2. Let generator run at no-load for a few minutes, to stabilize internal engine generator temperatures. 3. Place the Start/Stop switch in its STOP position. 2.7 APPLYING LOADS TO GENERATOR When applying electrical loads to the generator, observe these guidelines: • Before applying electrical loads, let the generator stabilize and warm up for a minute or two. 8 DO NOT overload the generator. ♦ 2.7.1 LETTING THE ENGINE STABILIZE The generator supplies correct rated voltage only at the proper governed speed. Some electrical appliances may be extremely sensitive to voltage. Incorrect voltages can damage such appliances. If electrical loads are applied at reduced operating speeds, such loads imposed on the engine when sufficient power is not available may shorten engine life. Never turn ON electrical loads until after the generator engine has started and stabilized at no-load. 2.8 SUMMER/WINTER HEAT RISER SYSTEM Under certain weather conditions, it is possible for ice to form in the venturi area of the carburetor. This condition can be very dangerous because it can prevent the governor system from functioning properly, which results in a “runaway” engine. The most common weather conditions leading to this problem are temperatures in the range of 25° F to 35° F (-4° C to 1.7° C), along with high humidity. This ice formation also can be attributed to the load being applied during these weather conditions. Generators running with no-load or light loads applied usually have the most problems. The Summer/Winter Lever (Figure 2.2) should be in the WINTER position for ambient temperatures below 40° F (4.4° C) and in the SUMMER position for ambient temperatures above 40° F (4.4° C). Figure 2.2 - Heat Riser System WINTER POSITION When the heat riser is in the SUMMER (down) position (Figure 2.2), air is drawn into the air cleaner from the upper intake tube. When the heat riser is in the WINTER (up) position, air is drawn from the lower intake tube, which is positioned to draw the heated air near the exhaust manifold. To prevent carburetor icing, the owner/operat...

Ce manuel est également adapté pour les modèles :
Electricité - 04164-1 (9.56 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories