Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
b)Only the type of fuel specified on the heater’s data plate shall be used. c) All flame, including the pilot light, if any, shall be extinguished and the heater allowed to cool, prior to fueling. d)During fueling, all fuel lines and fuel- line connections shall be inspected for leaks. Any leaks shall be repaired prior to returning the heater to service. e)At no time shall more than one day’s supply of heater fuel be stored inside a building in the vicinity of the heater. Bulk fuel storage shall be outside the structure. f) All fuel storage shall be located a minimum of 25 feet from heaters, torches, welding equipment, and similar sources of ignition (exception: the fuel reservoir integral with the heater unit). g)Whenever possible, fuel storage shall be confined to areas where floor penetrations do not permit fuel to drip onto or be ignited by a fire at lower elevation. h)Fuel storage shall be in accordance with the federal, state, or local authority having jurisdiction. • Never use heater where gasoline, paint thinner, or other highly flammable vapors are present. • Follow all local ordinances and codes when using heater. • Heaters used in the vicinity of tarpaulins, canvas, or similar enclosure materials shall be located a safe distance from such materials. The recommended minimum safe distance is 10 feet. It is further recommended that these enclosure materials be of a fire retardant nature. These enclosure materials shall be securely fastened to prevent them from igniting or from upsetting the heater due to wind action. • Use only in well-vented areas. Before using heater, provide at least a threesquare- foot opening of fresh, outside air for each 100,000 Btu/Hr of rating. This heater produces carbon monoxide, which is listed by the State of California as a reproductive toxin under Proposition 65. • Use only in places free of flammable vapors or high dust content. • Use only the electrical voltage and frequency specified on model plate. • Use only a three-prong, grounded extension cord. • Minimum heater clearances from combustibles: Outlet: 8 Ft. Sides: 4 Ft. Top: 4 Ft. Rear: 4 Ft. • Locate heater on a stable and level surface if heater is hot or running or a fire may occur. • When moving or storing heater, keep heater in a level position or fuel spillage may occur. • Keep children and animals away from heater. • Unplug heater when not in use. • When used with thermostat, heater may start anytime. • Never use heater in living or sleeping areas. • Never block air inlet (rear) or air outlet (front) of heater. • Never move, handle, refuel, or service a hot, operating, or plugged-in heater. • Never attach duct work to front or rear of heater. • Warning to New York City Residents For Use Only At Construction Sites in accordance with applicable NYC codes under NYCFD certificate of approval #4803, #4899, #4908, #4909, or #4934. UNPACKING 1. Remove all packing items applied to heater for shipment. 2. Remove all items from carton. 3. Check items for shipping damage. If heater is damaged, promptly inform dealer where you bought heater. 2 104193 OWNER’S MANUAL PRODUCT IDENTIFICATION Lower Shell Hot Air Outlet Fan Guard Fuel Tank Side Cover Fuel Cap Upper Shell Power CordIgnition Control Assembly (assembly on Thermostat Knob inside of side cover) Figure 1 - Portable Forced Air Heater ASSEMBLY These models are furnished with wheels and a front handle. Some models are furnished with a rear handle also. Wheels, handle(s), and the mounting hardware are found in the shipping carton. TOOLS NEEDED • Medium Phillips Screwdriver • 3/8" Open or Adjustable Wrench • Hammer 1. Slide axle through wheel support frame. Install wheels on axle. IMPORTANT:When installing wheels, point extended hub of wheels toward wheel support frame (see Figure 2). 2. Place cap nuts on axle ends. Gently tap with hammer to secure. 3. Place heater on wheel support frame. Make sure air inlet end (rear) of heater is over wheels. Line up holes on fuel tank flange with holes on wheel support frame. 4. Place front handle (and rear handle if provided) on top of fuel tank flange. Insert screws through handle(s), fuel tank flange, and wheel support frame. Attach nut finger tight after each screw is inserted. 5. After all screws are inserted, tighten nuts firmly. Front Handle Wheel Support Frame Wheel Hot Air Outlet Fuel Tank Flange Screw Nut Cap Nut Rear Handle Extended Hub Axle Air Inlet Figure 2 - Wheel and Handle Assembly 104193 3 115,000 Btu/Hr H.S.I. Series PORTABLE FORCED AIR HEATER FUELS WARNING: Use only kerosene or No. 1 fuel oil to avoid risk of fire or explosion. Never use gasoline, naphtha, paint thinners, alcohol, or other highly flammable fuels. Do not use heavy fuels such as No. 2 fuel oil or No. 2 Diesel. Using heavy fuels will result in a clogged fuel filter and/or nozzle. IMPORTANT: Use a KEROSENE ONLY storage container. Be sure storage container is clean. Foreign matter such as rust, dirt, or water will cause the ignition control assembly ...