Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Feet will install over raised areas underneath base weight. 3. Being careful not to scratch paint, lay cabinet base onto back side (use foam packaging block to support rear top of cabinet base). Align holes in bottom edges of cabinet base with holes in base as shown in Figure 4. Attach with 1 screw (C), 1 washer (D) and 1 nut (E) for each of the 9 holes (see Figure 4). Set assembly upright. 4. Attach base to weight with 4 screws (A) and 4 washers (B) as shown in Figure 4. 5. Install chain retainers (“S” hooks) to upper edges of cabinet base as shown in Figure 4. 6. Install electronic ignitor through cabinet wall as shown in Figure 4. Hand tighten. 7. Attach tank door to cabinet with 4 screws (F) and 4 nuts (G) as shown in Figure 4. Set entire assembly aside. Wheel Axle Nut Base Figure 3 - Attaching Wheels to Base Retainer Ring Chain Retainer Ignitor Ignitor Cap Cabinet Base Tank Door AFHBJCDEGI Base Base Weight Base Foot, Washer and Hex Bolt Figure 4 - Cabinet Base Assembly Burner and lightpost assembly 1. Locate 4 lightpost panels that are packaged together. Assemble 3 of the pieces with 4 screws (H) as shown in Figure 5. 2. Place lightpost top over panel assembly aligning screw holes. Attach with 3 screws (H) as shown in Figure 5. 3. Pilot light and wiring has been placed inside top of burner assembly for shipping. Carefully remove pilot from inside assembly and let wiring and pilot hang down back of assembly. 4. Place lightpost panels and top assembly on top of burner assembly aligning back side of each assembly. See Figure 6. Attach with 3 screws (H). 5. Place pilot assembly on top of lightpost top as shown in Figure 7. Attach with 4 screws (H). Check wire connections before proceeding. 6. Attach 4 light shroud screens to light shrouds with 4 screws (F) and 4 nuts (G) each as shown in Figure 7. Only 2 of the 4 screens are shown. 7. Place deco light shrouds on top of lightpost top (see Figure 7). Make sure flanges are on top. Slide shroud tabs together. Attach to lightpost top with 4 screws (H) through holes in bottom of shroud pieces (see Figure 7). Tighten all screws. 8. Attach lightpost top cap to shroud assembly with 4 screws (H) as shown in Figure 7. Assembly Continued Lightpost Assembly Open Side of Panel Assembly to Back of Heater Pilot Light Wiring to Back of Heater Burner Assembly Figure 6 - Connecting Lightpost and Burner Assembly Lightpost Top Cap Deco Light Shroud Screen Lightpost Top Pilot Assembly Lightpost Panels Lightpost Top Fourth Lightpost Panel Figure 5 - Lightpost Panels and Top Assembly Figure 7 - Attaching Pilot and Shroud Heater assembly Note: If needed, acquire assistance lifting assembly. 1. Place entire lightpost assembly on top of cabinet base assembly. Attach with 4 screws (H) as shown in Figure 8. Install 2 screws (H) into holes on each side of control valve. Attach control valve nut and control knob to control valve. 2. Connect 2 brown wires to ON/OFF switch. 3. Connect white ground wire attached to cabinet to right post on electronic ignitor. Remove wire tie. Connect black ignitor wire to left post on electronic ignitor. Install battery in ignitor as shown on page 12. 4. Install batteries in battery holder as shown on page 12. Do not mix batteries. 5. Connect regulator to gas cylinder, see Operation. Gas cylinder will sit inside of cabinet assembly. 6. Check for leaks. See Checking for Leaks page 8. 7. Attach fourth lightpost panel to assembly with 6 screws (H) as shown in Figure 7, page 6. Assembly Continued Operation CAUTION: Do not stand in front of heater while lighting. Stand at the side when lighting the heater. Use only a 20 lb. propane/LP cylinder (not included). See safety information for proper cylinder selection. Connect the hose/regulator assembly to the cylinder (see Figure 9). The hose should already be connected to the heater. Connect hose to the valve inlet (see Figure 9). Tighten firmly using a wrench. Route retention chain through at least one of the handles of the propane/LP tank (see Figure 9). Make sure to route chain through handle on tank and NOT around tank valve. Chain must not interfere with valve. Attach hooks on both ends of chains to chain retainers installed on cabinet base (see Figure 8). Lightpost/ Burner Assembly Control Valve Control Valve Nut and Control Knob Chain Retainer Retention Chain Cabinet Assembly Valve Inlet Ignitor Hose/Regulator Assembly ON/OFF Switch 20 lb. Propane/LP Cylinder Figure 9 - Connecting Hose/Regulator Assembly to Propane/LP Cylinder Figure 8 - Attaching Lightpost/Burner Assembly to Cabinet Assembly Checking for leaks 1. Turn heater valve to OFF position. 2. Turn cylinder supply valve fully counter clockwise to OPEN position. 3. Use a noncorrosive leak detection solution to check the connection for leaks before attempting to light heater. If leak is found, turn cylinder valve to CLOSE and do not use until all leaks are corrected. Lighting instructions Gas Light 1. Press power switch to ON, gas light will automatica...