Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Consult last carrier immediately if damage is found. Table 1 shows furnace transition kit usage. are used when replacing an existing horizontal furnace with a GHR26 horizontal allows installation of the GHR26 furnace modification of the existing supply and plenums. Note -GHR26 units can only be installed These kits GSR14 furnace, tt without return air left side discharge when using these transition kits. Note -Some GSR14 units may have been installed with little or no clearance to the unit's top side. Since the GHR26 unit's vent exits this side, may be encountered, ff it is, field transitions may be required. GSR14 CABINET WIDTH inches (mm) Q3-50 21-1/4 (540) Q3-80 2t-1/4 (540) Q4/5-80 21-1/4 (540) Q4/5-t00 21-1/4 (540) Note -There is no direct replacement interference fabricated Refer to figure 1 for typical GSR14 installation. 1 -Set the thermostat to the lowest setting. 2 -Disconnect electrical power to GSR14 unit. 3-Shut off gas to GSR14 unit. 4 -Disconnect supply and return air plenums. 5 -Remove control access panel, 6 -Cut combustion air intake pipe and exhaust pipe in location(s) which will allow convenient reconnection of pipes to GHR26 unit, and/or removal of muffler(s) (if installed), Remove muffler(s) (if installed). Support intake and exhaust pipes to prevent damage to pipe joints, 7 -Cut condensate drain line in a location which will allow convenient reconnection with GHR26 unit. 8 Disconnect gas line at unit. 9 Disconnect power wiring at unit, 10 -Disconnect low voltage wiring at unit. 11 -Remove blower access panel. 12 -Remove filter from inside of unit (if present) and disconnect return air plenum at unit. Note -Existing GSR14Q4/5-80/100 filter can be used in GHR26Q4/5-100 13 -Remove GSR14 unit. TABLE 1 GHR26 Q2/3-50 Q3-75 Q4/5-100 Q4/5-100 for GSR14Q4-50 unit Page 1 CABINET WIDTH inches (mm) 16-1/4 (413) t6-1/4 (413) 21-1/4 (540) 21-1/4 (540) with a GHR26 unit. units. KIT CAT# (LB#) 16L44 (LB-93421A) 16L44 (LB-93421A) 16L45 (LB-93422A) 16L45 (LB-93422A) TYPICAL GSR14 HORIZONTAL APPLICATION INTAKE PIPE 3T PIPE CONTROL ACCESS PANEL GASCONNECTOR------DRAIN PAN SUPPORT _FRAME FIGURE 1 Page 2 Note -Installation must conform with these instructions and the installation instructions packaged with the GHR26 furnace. Note -The overall dimensions of the GHR26 and the awkwardness of handling the GHR26 are increased once transitions are installed. A -Return Air Transition installation. Refer to figure 2, 1 -Lay GHR26 unit on its back (exposed internal parts facing up), (Figure 2 shows installed position.) 2 -Remove the three rear-most cabinet screws at return air inlet (3 each side), 3 -Cut two strips from roll of adhesive-backed foam tape (provided) to fit two cabinet sides as shown in figure. Apply to cabinet sides. 4 -Install transition as shown. 5-Install filter as shown in GHR26 installation instructions. GHR26Q4!5-100 unit will accept installation of GSR14Q4/5-80!100 unit filter. GHR26-50 and -75 units require a field provided 14x25x1 filter. B -Supply Air Transition Installation. Refer to figure 2. t -Remove the three rear-most cabinet screws at supply air inlet (3 each side). 2 -Cut two strips from roll of adhesive-backed foam tape (provided) to fit two cabinet sides as shown in figure. Apply to cabinet sides. 3 -Install transition as shown. C -Base Rails Installation, Refer to figure 2 1 -Install base rails as shown in figure 2. D -Unit Installation 1 -Align unit with existing supply air plenum (coil cabinet in air conditioning applications) and return air plenum, Make connections to unit. 2-Connect low voltage wiring as illustrated in GHR26 installatio...
Ce manuel est également adapté pour les modèles :électrique - 16L45 (166.74 kb)