Évaluations - 1, GPA: 4 ( )

Fabricant : Blue Rhino Taille : 888.96 kb Nom Fichier : Langue d'enseignement:

Make sure the burner pipe fits over the orifice. A WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury, or damage to property. If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for assistance. Tank/Gas Line Connection 1. Make 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts water. 2. Make sure control knobs are “OFF”. 3. Attach (1) 14.1 oz or (1) 16.4 oz or LP Gas LP gas tank. Note: if using a 20 lb LP gas tank, turn control valve to “OPEN”. 4. Spoon leak check solution at all “x” and arrow locations. (Figures 8-10) 5. If any bubbles appear: a. Disconnect gas tank per disconnecting instructions. b. Reconnect gas tank per connecting instructions. c. Repeat “Checking for Leaks” If you continue to see bubbles after several attempts, disconnect gas tank per disconnecting instructions and contact 1.800.762.1142 for assistance. If no bubbles appear after one minute turn tank “OFF”, wipe away solution and proceed. Contact 1.800.762.1142 for assistance. Do not return to place of purchase. page no. 7 Operating Instructions (continued) Before Turning Gas Supply “ON” A WARNING: Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it inside a building, garage, or any other enclosed area. A WARNING: Make sure surrounding areas are free of combustible materials, gasoline, and other flammable vapors or liquids. 1. Ensure that there is no obstruction to air ventilation. 2. Be sure all gas connections are tight and there are no leaks. 3. Be sure the access panel is clear of debris. 4. Be sure any component removed during assembly or servicing is replaced and fastened prior to starting. Before Lighting 1. Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. 2. If relighting a hot heater, always wait at least 5 minutes for gas to dissipate. Lighting 1. Turn control knob to “OFF” position. (Figure 11) 2. Connect LP gas tank. 3. If using an 20 lb LP gas tank, turn LP gas tank valve “OPEN”. 4. Push in control knob and rotate to “ON/HIGH” position. This will activate the built-in ignitor and light the burner. If necessary, keep depressing and rotating knob until burner lights. (Figure 12) 5. Once burner is lit, hold control knob in for at least 30 seconds and release. 6. If burner does not stay lit, turn to “OFF” position and wait 5 minutes and repeat steps 2 and 3. 7. If ignitor does not light burner, use a lit match positioned against the bottom of emitter screen at burner location, and repeat steps 2 and 3. (Figure 13) 8. Once burner is lit, rotate knob to desired heating level. If you experience any ignition problem, turn off the heater and gas supply, and consult “Troubleshooting”. A Caution: Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke. Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the control knob to the “LOW” position. Then, turn the knob to the level of heat desired. Figure 11 When heater is “ON”: 1. Emitter screen will become bright red due to intense heat. The color is more visible at night. 2. Burner will display tongues of blue flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. 3. If yellow flame is detected, turn off heater and gas supply and consult “Troubleshooting”. 4. Visually check burner flames at each use and make sure flame height matches illustration. (Figure 14) Re-lighting Note: For your safety, control knob cannot be turned on without first depressing control knob in off position and then rotating to on. 1. Turn gas control knob to off. 3. Repeat the “Lighting” steps 2 and 3. Turning Off 1. Rotate gas control knob to off position. Normally, burner will make a slight popping sound when extinguished. 2. Turn off gas at LP gas tank, or unscrew 14.1 oz or 16.4 oz LP gas tank. 3. Remove access panel. 4. Unscrew gas line from regulator. 5. Close access panel. Note: After use, some discoloration of the emitter screen is normal. Cleaning and Care Notices 1. Abrasive cleaners will damage this product. 2. Never use oven cleaner to clean any part of heater. 3. Do not clean any heater part in a self cleaning oven. The extreme heat will damage the finish. 4. More frequent cleaning may be required as necessary. It is imperative that control compartment, burners and circulating air passageways of the heater be kept clean. 5. Spiders and insects can create a dangerous condition that may damage heater or make it unsafe. Keep burner area clean of all spiders, webs, or insects. Clean b...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :