Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Secure with three nuts. Place dome cap over center bolt, making sure that the three slots in cap lay over each Rib Thread on finial until tight. Owner’s manual: model 200209 outdoor patio heater 7/28/04 10 ® Va« Endless Summer^ Step 10 - Secure Gas Line Make sure angled side of Gas Clip pokes up through large hole in Platform. Tighten screw until Gas Line is held securely in place. Stand Heater upright. Caution Before you attempt to use a propane tank, understand all tank and propane related precautions in Section #1 -“Safety First.” Contact 1-800-762-1142 for assistance. Do not return to place of purchase. SECTION VIEW Caution Your Endless Summer Heater has been checked at all factory connections for leaks. Recheck all connections, as movement in shipping can loosen connections. Check for leaks even if your unit was assembled for you at the store. Step 11 - Connect Gas Line to Tank The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer. • Slide full Propane Tank onto Heater Base. • Attach Gas Line to Tank by turning black plastic knob clockwise over Tank valve until tight. Note: Be careful not to kink flexible hose of Gas Line. • Secure tank in place by attaching loose end of Tank Restraint Chain to hole in right leg. 11 Owner’s manual: model 200209 outdoor patio heater 7/28/04 Endless Summer^ Step 12 - Check for Leaks • Make 2-3 oz. of leak check solution by mixing one part liquid dishwashing soap and three parts water. • Turn tank valve ON. • Check Gas Line / Control Valve for leaks: • Spoon several drops of solution onto Gas Line and Control Valve connection. • Inspect the solution at the connection to look for bubbles. • If NO bubbles appear, then the connection is secure. • If bubbles appear, there is a leak - • Turn Tank valve OFF. • Loosen screw on Clip. • Release Gas Line fitting from control valve and re-attach making sure connection is secure (see Step 7). • Retighten Clip. • If you continue to see bubbles after several attempts, contact 1-800-762-1142 for assistance. Check Gas Line / Tank valve for leaks: • Turn tank valve ON. • Spoon several drops of solution onto Gas Line and Tank valve connection. • Inspect the solution at the connection to look for bubbles. • If NO bubbles appear, then the connection is secure. • If bubbles appear, there is a leak: • Turn Tank valve OFF. • Release Gas Line fitting from Tank valve and re-attach making sure connection is secure (see Step 11). • If you continue to see bubbles after several attempts, contact 1-800-762-1142 for assistance. • Turn Tank Valve OFF. Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Owner’s manual: model 200209 outdoor patio heater 7/28/04 12 ® Va« Endless Summer^ Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 13 - Replace Engine Access Panel • Slide Igniter wire onto Igniter post. • Slide tab at top of Access Panel into slot in Emitter bottom. • Rotate Panel down until holes line up at bottom. • Secure Access Panel in place with thumbscrew. • Replace Control Knob. Step 14 - Install Igniter Battery Note: This step is required only for models with electronic ignition. • Remove battery cover cap by turning cap counterclockwise. • Install (1) AA battery. Negative end of battery goes in first. • Replace battery cover cap by turning cap clockwise. Note: Once you have successfully completed assembly steps 1-14 you are ready to begin operating your heater. 13 Owner’s manual: model 200209 outdoor patio heater 7/28/04 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. ® Vif-V Endless Summer^: Operation Caution: Do NOT attempt to operate heater until you have read and understand all precautions in section 1 “Safety First.” Before Turning Gas Supply ON • Your heater was designed and approved for OUTDOOR USE ONLY DO NOT use it inside a building, garage, or any other enclosed area. • Make sure surrounding areas are free of combustible materials, gasoline, and other flammable vapors or liquids. • Ensure that there is no obstruction to air ventilation. • Be sure all gas connections are tight and there are no leaks. • Be sure the access panel is clear of debris. • Be sure any component removed during assembly or servicing is replaced and fastened prior to starting. Before Lighting • Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. • If relighting a hot heater, always wait at least 5 minutes. • Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose assembly specified by manufacturer. Lighting Note: This heater is equipped with a Pilot Light that allows for safer startups and shutdowns. P...