Évaluations - 2, GPA: 4.5 ( )

Fabricant : CFM Corporation Taille : 531.89 kb Nom Fichier : Langue d'enseignement:

Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. Operating Information This is a propane, direct-fired, heater. Its intended use is primarily temporary heating of buildings under construction, alteration or repair. A WARNING: Not for home or recreational vehicle use. Propane is heavier than air. If propane leaks from a connection or fitting, it sinks to the floor, collecting there with the surrounding air, forming a potentially explosive mixture. Obviously, propane leaks should be avoided, so set up the propane supply with utmost care. Leak check new connections or reconnections with a soap and water solution and follow all connection instructions herein. Also ask your propane dealer for advice on the propane supply installation and ask him to check it if there are any questions. Direct-fired means that all of the combustion products from burning propane enter the heated space. Even though this heater operates very close to 100 percent combustion efficiency, it still produces small amounts of carbon monoxide. Carbon monoxide (called CO) is toxic. CO can build up in a heated space and failure to provide adequate ventilation could result in death. The symptoms of inadequate ventilation are: headache dizziness burning eyes and nose nausea dry mouth or sore throat So, be sure to follow advice about VENTILATION in these operating instructions. WARNING: Do not look over top of heater (reflector) during ignition. This heater may produce a small puff of flame during ignition, which could result in serious bodily injury. Lighting Instructions when Using Piezo A WARNING: Review and understand the Safety Information on page 3 before lighting the Tank Top Heater. A CAUTION: Due to high surface temperature, keep children, clothing and furniture away. Keep burner and control compartment clean. This heater shall not be installed in a bedroom or a bathroom. A WARNING: Hot while in operation: Do not touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away. 1. Stop! Read all safety information. 2. Check that gas supply to the heater is on. 3. Turn heater regulator knob clockwise x to “OFF” position. 4. Wait five (5) minutes to clear out any air. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information on the side of heater. If you do not smell gas, go to the next step. 5. Turn heater regulator knob counterclockwise to “Hi” position. Press in safety shut-off valve plunger for five (5) seconds. (Fig. 3) NOTE: The first time the heater is operated after connecting the gas supply, the safety shut-off valve plunger should be depressed for about thirty (30) seconds. This will allow air to bleed from the gas system. 6. With safety shut-off valve plunger pressed in, push down and release piezo ignitor button. This will light pilot. If needed, keep pressing piezo ignitor button until pilot lights. 7. Keep safety shut-off valve plunger pressed in for thirty (30) seconds after lighting pilot. After 30 seconds, release safety shut-off valve plunger. 8. If burner goes out, repeat steps 5 through 7 or use a match. If heater will not light after repeated attempts, do not attempt to repair heater. Return heater to nearest authorized service center or to the address on back of this manual, freight prepaid. 9. When burner is lit, turn heater regulator knob to desired heat setting (LO, MED, HI). 10.Light both burners when maximum heat is needed. Use one burner to conserve fuel. To Turn Off Heater 1. Tightly close propane tank valve by turning clockwise. 2. Turn the heater regulator knob to the “OFF” position. Wait at least 15 minutes for the heater to cool before handling heater. 3. Always remove the heater from the propane tank after each use. Do not store heater while attached to propane tank in an enclosed area. 5 Lighting Instructions when Using Match Read and understand all safety information before operating heater. A WARNING: Do not raise burner heads and cover air inlet holes in mixing tube with burner bracket. A WARNING: Make sure there is no open flame in the area. Fully open the propane tank valve. 1. Turn heater regulator knob counterclockwise to the “Hi” position. (Fig. 3) A WARNING: Stand to the side of unit while lighting. Do not stand or have any part of your body over or in front of heater while lighting. 2. Do not attempt to light one burner off of the other. Use one match per burner. Locate ignition hole in side of burner. (Fig. 4) Hold a lit match under ignition hole. A CAUTION: Do not insert match into air inlet holes in mixing tube. Fig. 4 Place lit match under ignition hole. 3. Push in the safety shut-off valve plunger (Fig. 3) A WARNING: Do not push in safety shut-off valve plunger before inserting lit match. 4. Burner should light. Mesh screen on burner glows red when lit. After burner is lit, continue holding i...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :