Évaluations - , GPA: ( )

Instructions Monessen Hearth, Modèle BUF500

Fabricant : Monessen Hearth
Taille : 695.45 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

BEFORE YOU START Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately inform the dealer from whom you purchased the appliance. Do not attempt to install any part of the appliance unless you have all the parts in good condition. Make sure you have received all parts Check your packing list to verify that all listed parts have been received. You should have the following: 1. Vent-Free Gas Firebox 3. Five (5) sheet metal screws for canopy 2. Canopy 4. Installation and Operating Instructions What you will need for installation TOOLS BUILDING SUPPLIES • Phillips screwdriver • Square • Framing materials • Hammer • Piping complying with local codes • Wall finishing materials • Saw and/or sabersaw • Tee joint • Caulking material (noncombustible) • Level • Pipe wrench • Fireplace surround materials (noncombustible) • Measuring tape • Pliers • Electric drill and bits • Pipe sealant approved for use with propane/L.P.G. (resistant to sulfur compounds) Refer to the installation instructions provided with the log sets for items required for log set installation. notice Illustrations shown in this manual reflect “typical” installations with nominal dimensions and are for design and framing reference only. Actual installations may vary due to individual design preferences. However, always maintain minimum clearances to combustible materials and do not violate any specific installation requirements. GENERAL INSTALLATION INFORMATION In planning the installation for the appliance it is necessary to determine where the unit is to be installed and whether optional accessories are desired. Gas supply piping should also be planned. The following steps represent the normal sequence of installation. Each installation is unique, however, and might require a different sequence. 1. Position firebox prior to framing or into prepared framing. 2. Field wire main power supply to models with fan kit. (Electrical connections should only be performed by an experienced, licensed /certified tradesman). Electrical outlet is needed with fan kit. 3. Plumb gas line. (Gas connections should only be performed by an experienced, licensed/certified tradesman). 4. Install vent-free gas log heater per the instructions provided with the vent-free gas log heater. 5. Complete finish wall material, surround and optional hearth extension to your individual taste. FIREBOX EXTERNAL DIMENSIONS BUF400: 2413/16" 23/16" 69/16" 103/8" 147/16" BUF400: 40" BUF400: 36" 241/4" 61/2" 219/16" 21" 34" 6" 2" BUF500: 3013/16" BUF500: 46" BUF500: 42" Figure 1 - Firebox Dimensions GENERAL INSTALLATION INFORMATION 17" 211/2" BUF400: 351/2" BUF400: 203/8"BUF500: 263/8" BUF500: 411/2" MINIMUM HEARTH DIMENSIONS Figure 2 - Minimum Hearth Dimensions location of firebox Carefully select the best location for installation of your vent-free firebox. The following factors should be taken into consideration: • Clearance to side wall, ceiling, woodwork and windows. See “Clearances/Height Requirements on page 8. Minimum clearances to combustibles must be maintained. • Location must not be affected by drafts caused by kitchen exhaust fans, ceiling fans, return air registers for forced air furnaces / air conditioners, windows or doors. • Installation must provide adequate ventilation and combustion air. • DO NOT INSTALL THIS FIREBOX IN A BEDROOM OR BATHROOM. • Location should be out of high traffic or windy or drafty areas. • DO NOT INSTALL WHERE CURTAINS, FURNITURE, CLOTHING OR OTHER FLAMMABLE OBJECTS ARE LESS THAN 42" FROM FRONT OF HEATER. • Never obstruct the front opening of the vent-free firebox or restrict the flow of combustion and ventilation air. • Minimize modifications to existing construction. Refer to Figure 3 below for location suggestions. • Do not install in the vicinity where gasoline or other flammable liquids may be stored. The vent-free firebox must be kept clear and free from these combustible materials. Figure 3 - Location of Firebox CLEARANCES and HEIGHT REQUIREMENTS Ensure that minimum clearances shown in Figures 4 through 7 are maintained. Left and right clearances are determined when facing the front of the firebox. Follow these instructions carefully to ensure safe installation. Failure to follow these requirements may create a fire hazard. 1. Sidewall clearances: The clearance from the inside of the appliance to any combustible wall should not be less than 9". See Figure 4. 2. Ceiling clearance: The ceiling must be at least 42” from the top of the firebox opening. See Figure 4. 3. Back wall clearnace: The appliance may be placed against a combustible back wall. 9" Minimum42"Minimum9"Minimum Figure 4 - Clearance and Height Requirements Continued on page 10 CLEARANCES and HEIGHT REQUIREMENTS 4. Mantel clearances: The canopy supplied with the unit must be installed. If a combustible mantel is installed, it must meet the clearance requirements as shown in Figure 5. 12" 10" 8" 6" 23" 21" 21/2" 19" 16" 12" Figure 5 - Mant...