Évaluations - 4, GPA: 4.5 ( )

Fabricant : Desa Taille : 2.78 mb Nom Fichier : Langue d'enseignement:

Make sure propane/LP tank valve is clean. Check "O" ring on heater inlet fuel valve connector for damage before each use. Replace if worn or damaged. 27. The LP gas cylinder must be constructed and marked in accordance with the specifications for the LP gas cylinders of the US Department of Transportation (DOT) or Transport Canada. 28. Use only in accordance with local codes or, in the absence of local codes, with the CAN1- B149 Installation Code. 29. Storage of heater is permissible only if the cylinder is disconnected and removed from heater. 30. Always remove heater from propane tank after each use. Always store propane tank outdoors in a well ventilated space out of the reach of children. Never store propane tank in a building, garage, or any other enclosed area. Never store propane tank near high heat, open flame, or where temperatures exceed 100° F (38° C). Assembly Instructions 2 Burner Models ONLY 1. Inspect the heater components for possible shipping damage. If any is found, immediately notify the dealer. Check to make sure that all components are included with your heater (see pages 8 and 9). 2. Insert the piezo ignitor into the bracket on the burner support bracket as shown in Figure 1. Tighten the piezo mounting nut. Do not over tighten the nut. 3. Connect the burner hoses together as shown in Figure 2. Wrench tighten to insure leak tight connection. 4. Mount the burner assembly onto the support arm using the burner head mounting brackets and brass screws as shown in Figure 3. Place side of bracket into the slot on support arm. Secure with screw. Make certain that the air holes on the sides of the burner tube are not blocked. Securely tighten the burners into place. Safety Information Continued Piezo Ignitor Piezo Mounting Nut Burner Support Bracket Figure 1 - Installing Piezo Ignitor Figure 2 - Attaching Burner Hoses to Regulator Burner Head Assembly Support Arm Slot Air Hole Burner Head Mounting Bracket Brass Screw Figure 3 - Attaching Burner Head Assembly to Support Arm 5. Attach the electrode wires to the piezo ignitor as shown in Figure 4. Support Arm Safety Information Continued Support Arm Bracket Bolt Piezo Ignitor Regulator Electrode Wires Figure 5 - Attaching Support Arm and Regulator to Propane/LP Tank Figure 4 - Attaching Electrode Wires to Piezo Ignitor Operating Instructions 1. Check heater for damage. If heater is damaged, promptly inform dealer where you bought heater. 2. Follow all of the safety and operating precautions. 3. Check the "O" ring on the POL before each use. Replace the "O" ring if there is any sign of wear or damage. 4. Make sure heater regulator knob is in the "OFF" position. 5. 2 Burner Models Only Attach the heater to the guard on the propane/LP cylinder with the support arm on the inside of the guard and bolts through two holes in the guard (see Figure 5). Tighten the support arm bracket into place using the wing nuts provided. 6. For All Models Connect the POL fitting at regulator to the propane/LP cylinder by rotating the POL nut counter clockwise into the propane/LP cylinder's valve outlet and securely tighten with a wrench. WARNING: Attach heater in upright position. Never attach heater in a horizontal position. This could lead to dangerous flare-ups or fire. 7. Securely tighten all gas connections. 8. Open the cylinder's gas valve and check all connections for leaks. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak that must be corrected. DO NOT USE A FLAME. To START Heater WARNING: When lighting the heater DO NOT look over top of heater (reflector). Stand to the side of the heater during ignition. Do not stand or have any part of your body in front of the heater. WARNING: MAKE SURE THERE IS NO OPEN FLAME IN THE AREA. Fully open the valve on the propane/LP cylinder. Read all lighting instructions before attempting to ignite heater. 1. Turn the heater regulator knob counterclockwise to the "HI" position. 2. Repeatedly push and release the piezo ignitor (dual burner), or place a lighted match near the face of the heating element (mesh screen) of the burner you are lighting, using the hole located on the side of the reflector. See Figure 6. Red Button on Safety Valve Figure 6 - Lighting Heater With a Match CAUTION: Do not light at the orifice. 3. Depress the red button on the safety valve admitting gas to the burner (see Figure 6, page 5). WARNING: Do not depress red valve button before repeatedly activating the piezo or inserting match. 4. When the gas on the face of the mesh screen lights, continue to hold the valve button depressed for 30 seconds, then release. 5. If flame goes out, wait 5 minutes and repeat the lighting procedure. 6. If heater will not light after repeated tries, do not attempt to repair heater. Return heater to nearest authorized service center or to manufacturer of this product. 7. For dual burner models, repeat steps 1 through 4 to ignite the other burner. 8. After both burners or single burner, are lit...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :