Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
Please read the installation, operating and maintenance instructions thoroughly before installing operating or servicing this appliance *** THINK SAFETYf * After appliance shut down. do NOT touch or move unit for at least 30 minutes. This allows for proper cooling of heater components. ‘ At least once a year, the unit should be inspected for the presence of spiders, spider webs, or otner insects. The burner area is a common spider haven and can damage the healer and render it unsafe for use Check the heater immediately if any of the following exists: 1 The smell of gas in conjunction with extreme yellow tipping of the burner flames. 2 The heater does not reach maximum temperature 3 The burner makes a popping noise during use (a slight popping noise is normal when the burner is extinguished.)_ * The LP regulator/hose assembly shall be kepi completely inside cylinder housing * Children and adults should be aware of the hazards of high surface temperatures and should use extreme caution and keep proper distance away from main heater unit lo avoid bums or clothing ignition ' Young children should be carefully supervised when they are in the area of the heater * Clothing or other flammable materials should not be hung from the heater, or placed on or near the heater * Any guard or other protective device removed for servicing the heater must be replaced prior lo operating the heater. * Installation and repair should be done by a qualified service person The heater should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required. II is imperative that control compartment, burner and air circulation passageways of the healer be kept clean & clear of debris, insects spider webs, elc. ■ Keep the appliance area clear and free of combustion matenals gasoline and other flammable vapors and liquics * Do not obstruct Ihe flow of combustion and ventilation air * Keep Ihe ventilation opening of the cylinder housing enclosure free and clear of debris * Save these instructions! Retain in a safe place for future reference. _ _ _ _ *** IMPORTANT NOTICE *** - Do NOT return to place of purchase!!! Please contact our Toll Free Hotline: (866) 985-7877 E-mail: cservice@welltraveled.net TQOL? AND PART? NEEDED FQR ASSEMBLY NOTE: 20 Pound. 5 Gallon Capacity - Standard LPG Tank/Cylinder is NOT supplied Tools Needed: Adjustable Wrench Phillips Head Screwdriver (#2 or #3 blade) Spray Bottle of Soapy Water or Paint Brush and Soapy Water (to check for leaks) Parts Supplied: * Mam Burner/Head assembly unit w/ flexible gas hose * 1 pc 18" Cylinder Base * LPG Tank housing unit * 34" Support Post (2pcs components see fig B-2) * Post Support Brackets (3 cach) * LPG Gas Regulator with Hose * 32" Aluminum Reflector Hood (5 pc. components, see fig. D) * 4 ea. - M6 x 10mm bolts for Burner Assembly & Upper Post ‘ B-1 6 ea. - M6 x 35mm long bolts with M6 nuts and washers for Post Brackets B-2 4ea-M6 x 10mm bolts for pole assembly * 3 ea. - M8 x 16mm short bolts for Post Bracket to Cylinder Base • 1/4" cap nuts for attaching reflector hood components - Large wing nut to attach reflector hood to burner head Fig A Fig B Fig.C Fig.D FigE Fig.F ‘ 12 ea. ' 3 ea unit ‘ 6 ea. M6 x 25mm bolts to attach wheel assembly brackets *** IMPORTANT NOTICE *** The installation must conform with local codes or, in the absence of local codes, with the most current version of the National Fuel Gas Code, ANSIZ223.1 ASSEMBLY INSTRUCTIONS STEP 1: 1-1. Place the 3 post mounting brackets on the Cylinder Base as shown. 1-2. Use 3-M8 x 15mm bolts to secure brackets to the base. STEP 1a: 1a-1. Attach wheel assembly brackets to cylinder base. Align holes and position as shown. Thread 3, M6 x 25mm bolts per bracket and tighten securely. (Do not overtighten.) STEP 2: 2-1. Place the tall upright the base of support post onto the top of the post brackets .aligning pre-dri lied holes as shown. 2-2. Use 6-M6 x 35mm bolts, washers & nuts to attach post to post brackets. Tighten securely 2-3. Put the pole onto the base of support post and use 4-M6x 10mm bolts to fix it. STEP 3: Carefully, slide the tank cover over the post and onto the cylinder base. Tank cover should fit into pre-molded slots in base unit. For questions, replacement parts, service help, or other assistance, please call the Customer Service HotlineI *** IMPORTANT NOTICE *** - Do NOT return to place of purchase!!! Please contact our Toll Free Hotline: (866) 985-7877 E-mail: cservice@welltraveled.net For questions, replacement parts, service help, or other assistance, please call the Customer Service Hotlinel PAGE 8 ASSEMBLY INSTRUCTIONS STEP 4: 4-1. Carefully insert gas inlet hose completely through the post resting heater head unit on the support post. 4-2. Make sure both components are level and aligned with one another and are at a 90 degree angle to the floor. Align the holes of the support...