Évaluations - 4, GPA: 3.5
(
)
)
|
Facilité d'utilisation
' 3 ea unit ‘ 6 ea. M6 x 25mm bolts to attach wheel assembly brackets *** IMPORTANT NOTICE *** The installation must conform with local codes or, in the absence of local codes, with the most current version of the National Fuel Gas Code, ANSIZ223.1 ASSEMBLY INSTRUCTIONS STEP 1: 1-1. Place the 3 post mounting brackets on the Cylinder Base as shown. 1-2. Use 3-M8 x 15mm bolts to secure brackets to the base. STEP 1a: 1a-1. Attach wheel assembly brackets to cylinder base. Align holes and position as shown. Thread 3, M6 x 25mm bolts per bracket and tighten securely. (Do not overtighten.) STEP 2: 2-1. Place the tall upright the base of support post onto the top of the post brackets .aligning pre-dri lied holes as shown. 2-2. Use 6-M6 x 35mm bolts, washers & nuts to attach post to post brackets. Tighten securely 2-3. Put the pole onto the base of support post and use 4-M6x 10mm bolts to fix it. STEP 3: Carefully, slide the tank cover over the post and onto the cylinder base. Tank cover should fit into pre-molded slots In base unit. For questions, replacement parts, service help, or other assistance, please call the Customer Service HotlineI *** IMPORTANT NOTICE *** - Do NOT return to place of purchase!!! Please contact our Toll Free Hotline: (866) 985-7877 E-mail: cservice@welltraveled.net For questions, replacement parts, service help, or other assistance, please call the Customer Service Hotlinel PAGE 8 ASSEMBLY INSTRUCTIONS STEP 4: 4-1. Carefully insert gas inlet hose completely through the post resting heater head unit on the support post. 4-2. Make sure both components are level and aligned with one another and are at a 90 degree angle to the floor. Align the holes of the support post with the holes at the bottom of the head unit. Attach using 4- M6 x 10mm bolts. Use a Phillips head screwdriver to tighten securely. STEP 5: 5-1. Place the 4 reflector components together, overlapping the edges as shown and fitting the pre-installed threaded studs through the pre-drilled holes. Attach using washers and cap nuts. 5-2. Position the round center component over the remaining exposed studs at the center and attach using washers and cap nuts. Tighten securely. STEP 6: 6-2. Place the assembled reflector hood over the 3 securing threaded bolts located on the top of the head unit. 6-2. Fit a washer onto each reflector support bolt and tightly secure with wing nuts. for mounting reflector hood to unit *** IMPORTANT NOTICE *** - Do NOT return to place of purchase!!! Please contact our Toll Free Hotline: (866) 985-7877 E-mail: cservice@welltraveled.net A [caution] SAFETY FIRST!!!- P Inspect the gas hose before each use of the appliance. P The hose/regulator assembly must be 'REPLACED prior to the appliance being put into operation if there is evidence of excessive abrasion or wear, or if the hose is damaged. P Any replacement assembly must meet original equipment manufacturer's specifications. STEP 7: 7-1. Raise the tank housing cover and place on the post plate as illustrated. 7-2. Fit the gas regulator flexible hose to the threaded end of the gas inlet hose. 7-3. Tighten the fitting nut of the hose to the inlet gas hose. Be careful not to overtighten. 7-4. Place LP gas tank into cylinder base. 7-5. Connect the regulator with the LPG gas tank. Note: left hand thread direction - Hand tighten securely using quick connect turn knob. Do not overtighten. For Your Safety If you smell gas: 1- Shut off gas to appliance 2- Extinguish any open flame 3- If odor continues, immediately call your gas supplier GAS REQUIREMENTS & LEAK TESTING NEVER CONNECT AN UNREGULATED GAS SUPPLY TO THE HEATER. PRECAUTIONS * Periodically check the whole system for leaks or if the smell of gas is detected. * Extinguish all open flames. Perform ALL leak tests outdoors. * Never leak test while smoking. * If you can not stop a leak, turn off the gas supply and call the Customer Service Hotline, or your local gas company. * For best results, the heater must be checked with a full cylinder. * Dq not use the heater until all connections have been leak tested and are sound!! * Only those parts recommended by the manufacturer should be used. Substitution can void the warranty. GAS REQUIREMENTS * Maximum inlet pressure to propane regulator must not exceed 125 PS.I. * A minimum supply pressure of 11.0 W.C. is required for the purpose of input adjustment for propane gas. * The pressure regulator and hose assembly supplied with the appliance MUST be used. Replacement pressure regulator and hose must conform to standards & specifications of the appliance manufacturer. * The installation must conform with local codes, or in the absence of local codes, with National Fuel Gas code, ANSI/NFPA 58 or ANSI Z233.1-1998. (Canada - CAN/CGA-B149.1 & 2-M86) PAGE 9 IMPORTANT NOTICE I - Do NOT return to place of purchase!!! Please contact our Toll Free Hotline: (866) 985-7877 E-mail: cservice@welltravele...