Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
It may be helpful to have someone assist you with the assembly. You will need the following tools (NOT INCLUDED): ** #2 or #3 Philips Screwdriver (or standard slotted screwdriver) ** Adjustable Wrench. Make sure you complete assembly on a clean, level, preferably carpeted location. A flat piece of cardboard will also work for assembly. Unpack and identify all components listed on page 3 of this manual and lay them out on the carpeted floor or piece of cardboard and then follow the steps below: STEP 1 Loosen and remove the top 2 screws on each side of the head unit (Part 1) and attach the angle adjustment handle (included with Part 1) as shown in Figure 1. FIGURE 1 Tighten the screws as shown in Figure 2. FIGURE 2 5 STEP 2 Using mounting bracket (Part 2), thread entire electrical cord through the mounting bracket as shown in Figure 3. FIGURE 3 STEP 3 Using 4 threaded bolts, attach mounting bracket (Part 2) to head unit (Part 1) as shown in Figure 4. FIGURE 4 STEP 4 Align tilt switch (black box on head unit, Part 1) to threaded holes on mounting bracket (Part 2) and insert small screws with flat washers as shown in Figure 5. FIGURE 5 6 STEP 5 Thread electrical cord through curved upper arm (Part 3) and attach with 4 threaded bolts as shown in Figure 6. FIGURE 7 FIGURE 8 FIGURE 6 STEP 6 Insert inner support tube (Part 4) inside telescopic body (Part 5) as shown in Figure 7. Tighten clamp collar as shown in Figure 8. STEP 7 Thread electrical cord through inner support tube and telescopic body as shown in Figure 9 and affix curved upper arm and inner support tube with one threaded bolt as shown in Figure 10. FIGURE 9 FIGURE 10 7 STEP 8 Thread electrical cord through base connection pole section (Part 6) and insert 4 threaded bolts as shown in Figure11, 12 and 13. FIGURE 11 FIGURE 12 FIGURE 13 STEP 9 Mount support collar flange (Part 7) to base assembly with wheels (Part 8) as shown in Figure 14, and secure with flat washer, lock washer, and .” bolt as shown in Figure 15. FIGURE 14 FIGURE 15 STEP 10 Carefully lift pole and head unit assembly and insert lower end of pole into support collar flange (Part 7) as shown in Figure 16. Secure with 6 threaded bolts. FIGURE 16 8 OPERATING INSTRUCTIONS This appliance MUST be grounded. * When using outdoors, we recommend using a certified GFI (Ground Fault Interrupt) outlet to protect against electrical shock. * ALL installations must be in accordance with I.E.E. safety regulations or equivalent. * Avoid the use of an extension cord with this appliance. If one is used, it must meet the requirements as outlined in #15, “Important Instructions” on page 4 of this manual. * Do not place any objects such as furniture, papers, clothing, or curtains closer than 3 feet to the front, top or sides of this heater. * ALWAYS unplug the heater when it is not in use. For optimal performance and safety concerns, we HIGHLY recommend that the Infrared Heating System be operated at a minimum of 98” in height or the maximum extended length of the telescopic body sections. You should only lower the height of the unit for storage purposes when it has completely cooled and is not in operation. To adjust the IR telescopic body: Pull up on the release levers of the tightening clamps and adjust tension using the tension knobs. Raise and lower the telescopic sections and/or swivel to desired position and then push in clamp levers to secure. DO NOT over tighten tension knobs. There should only be a moderate amount of tension to maintain the telescopic position of your heater. CAUTION! Step 1 Before turning on your Infrared Heating System, check to make sure the “On/Off” switch located on the tilt switch (black box) of the head unit is pulled OUT or in the ON position (note: to turn the heater “Off”, push in the switch). Next, extend all 3 telescopic sections to their maximum extended length. Release clamp levers and pull up on each of the sectional steel tubes until each tube stops. Then push in clamp levers to secure sections in place. Adjust the tension knobs as needed to maintain height position. Step 2 The Infrared Heating System comes equipped with a heavy duty, 16/3 gauge wire and grounded plug. This appliance must be used with an outlet that has been installed and grounded in accordance with local codes and ordinances. Make sure the heater is connected to an outlet having the same configuration as shown in the figure shown to the right. DO NOT use an adapter with this product. Check with a licensed electrician if the grounding instructions are not understood completely or if the wall outlet does not match the plug. Step 3 Your Mojave Sun, Infrared Heating System is ready to enjoy. Plug the appliance in and enjoy the warmth! 9 Specifications Model: 60253/60411 Voltage: 120 volts Amps: 13.0 amps Wattage: 1500 watts Lamp Type: Quartz Halogen Minimum Operational Height: 8 ft., 2 in. (98 in.) Assembled Weight: 53 lbs. Head Unit Dimensions: 18.72” x 9.85” x 6.7” Heater Assembled Dimensions: 22” diamet...
Ce manuel est également adapté pour les modèles :électrique - 60411 (717.62 kb)