Évaluations - 4, GPA: 4.5
(
)
)
|
Facilité d'utilisation
1-800-934-9194 LOCATION AND INSTALLATION (CONT.) CONNECTING THE POWER 1. Turn off the power at the main service 2. Remove the screw from the back of the unit to connect the power to the heater. 3. Attach the cable connectors to the unit and slide the 10 gauge wire through the cable connector. NOTE: For certain applications, conduit may be required. Check your local electrical codes. If you run the wiring in conduit and wish to be able to rotate the heater, be sure to purchase enough flexible conduit to allow the heater to be rotated. 4. Connect the wire to the power terminal block located in the base of the heater. 5. Turn on the power at the main service. OPERATION NOTE: The first time you operate this heater, it may emit a slight odor and some smoke. This is due to the residual cleaning agents used to clean the element during manufacturing. This is normal operation and will cease after the heater has been used for a few minutes. 1-800-934-9194 OPERATION (CONT.) ADJUSTING THE AIR FLOW DIRECTION 1. Rotating the unit - if the unit has been installed with a single lag bolt, simply rotate the entire unit as needed to adjust the direction of the air flow. 2. Tilting the unit - Loosen the bracket screws, tilt the heater to the desired position, and re-tighten the bracket screws. NOTE: To tilt the heater it must be mounted in bottom keyhole slots of mounting brackets to maintain adequate clearance and prevent possible overheating. 3. Adjust the louvers to the desired position. NOTE: The louvers are designed so they cannot be completely closed. Do not attempt to close the louvers completely as this may damage the unit. . To prevent possible electric shock, disconnect the power to the heater at the main service box before attempting to adjust the heat output of the unit. 1-800-934-9194 OPERATION (CONT.) WIRING DIAGRAM 1. It is recommended that #10 AWG wire be used in all installations for possible future reconnection at a higher wattage (Refer to the National Electric Code (NEC) for maximum run length to minimize voltage drop to 3% max. Circuit runs exceed 100 ft. may require larger conductor size). 2. Wires should be routed through the indicated element jumper wire eliminating the use of a wire tie. 1-800-934-9194 MAINTENANCE To prevent possible electric shock, disconnect the power to the heater at the main service box before attempting inspect or clean the unit. Use care to prevent damage to the internal components of the heater when cleaning the heating element. Make sure all connections remain tight and all wiring is routed away from the element fins when reassembling the unit. Allowing wiring to touch the element fins could result in a fire hazard. CLEANING THE FAN AND MOTOR Remove the protective grille from the rear of the heater. This provides access to the fan and motor. Wipe off the fan and motor with a soft cloth or brush. The fan motor does not require lubrication. Replace the protective grille when finished. 1-800-934-9194 WARRANTY One Year Limited Warranty Soleus International Inc. warrants the accompanying Soleus Air Heater to be free of defects in material and workmanship for the applications specified in its operation instruction for a period of ONE (1) year from the date of original retail purchase in the United States. If the unit exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of charge within a reasonable time after the unit is returned during the warranty period. As a condition to any warranty service obligation, the consumer must present this Warranty Certificate along with a copy of the original purchase invoice. THIS WARRANTY DOES NOT COVER: • Damage, accidental or otherwise, to the unit while in the possession of a consumer not caused by a defect in material or workmanship. • Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions in the instructions. This includes dents, accidental or otherwise, to the base and head of the unit. • Damage to the finish of the case, or other appearance parts caused by wear. • Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus International Inc. • Freight and Insurance cost for the warranty service. ALL WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY ARE LIMITED TO ONE-YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY. SOLEUS INTERNATIONAL INC. DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT SHALL SOLEUS INTERNATIONAL INC’S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS UNIT. This warranty covers only new products purchased from our authorized dealers or retailers. It does not cover used, salvaged, or refurbished products. As some states do not allow the limitation or exclusion of incidental or consequential d...