Évaluations - 5, GPA: 3.6
(
)
)
|
Facilité d'utilisation
The adapter should not be used if a three-slot grounded receptacle is available. DO NOT DEFEAT THE SAFETY PURPOSE OF THE GROUNDED PLUG. WARNING: It is normal for the power cord to feel warm to the touch; however, a loose fit between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified electrician to inspect the original outlet for damage. IN THE BOX • MICATHERMIC HEATER • REMOTE CONTROL • REMOTE CONTROL BATTERY • INSTRUCTION BOOKLET • WALL MOUNTING BRACKET • 4 - DRY WALL ANCHORS • 4 - MOUNTING SCREWS • 2 -LEGS • 2 -LEG SCREWS • 2 - MEDIUM BLACK SPRING WASHERS • 2 - MEDIUM GREY WASHERS • 4 - WHEELS • 4 - WHEEL SCREWS • 4 - SMALL BLACK SPRING WASHERS • 4 - SMALL GREY WASHERS PRODUCT DIAGRAM CARRY HANDLE & WALL MOUNT (on back) DIGITAL DISPLAY CONTROL PANEL LEGS WHEELS ASSEMBLY -REMOVING THE HEATER FROM THE PACKAGING Remove the heater from the box. NOTE: Product drawings may slightly differ from actual product. Assembly and packaging are the same as depicted in the drawings Remove the Styrofoam from both ends of the heater, and remove the plastic bag. Remove the 2 remaining bags from the box.. One bag contains: feet with casters. [Fig 1] The other bag contains: 1 mounting support, 4 screws and 4 drywall anchors for wall mounting. [Fig 2] Save the packaging for storing the heater while it is not in use or during summer months. Note: If any part is damaged or missing, do not use or attempt installation. Contact cus- tomer service for a replacement. ASSEMBLY -INSTALLATION Required Tools for Floor Use: Phillips screwdriver (not supplied) Estimated Assembly Time for Floor Use: 1 minute Assembly Instructions for Floor Use: Insert the feet and bolts onto the unit as shown in the diagram. Required Tools for Wall Mounting: Phillips screwdriver (not supplied) Drill (not supplied) Hammer (not supplied) Estimated Mounting Time: 5 minutes Mounting Instructions: STEP 1 Using the mounting support as a guide, mark the first screw hole on the wall. STEP 2 Move the mounting support, and drill the first screw hole. STEP 3 Insert the first mounting anchor into the drilled hole. STEP 4 Place the mounting support on the wall. Insert a screw through the mounting support and anchor. Tighten the screw lightly. STEP 5 Use the other side of the mounting support to mark the second screw hole on the wall [approximately 5 7/16 in.]. STEP 6 Move the mounting support, and drill the second hole. STEP 7 Insert the second mounting anchor into the drilled hole. STEP 8 Place the mounting support on the wall. Insert the second screw through the mounting support and anchor. Firmly tighten both screws. STEP 9 After mounting the heater, insert two screws into the bottom holes and secure the heater to the wall for safety purposes. OPERATING INSTRUCTIONS CONTROL PANEL & REMOTE OPERATION 1. Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power outlet. Only operate heater in upright position with caster wheels attached. 2. Turn the heater on by pressing the On/Off button on the control panel or the supplied remote control. 3. Select a heat setting: On the control panel, press the MODE button to toggle between the two heat settings; LOW (1000W) or HIGH (1500W) . When using the remote control press the HIGH or LOW buttons to select the preferred power setting. 4. Adjust the thermostat by pressing the TEMPERATURE SELECT buttons (J or K) on the control panel or remote control. The digital readout will display the selected temperature. 5. Once you have chosen the desired temperature, the heater will remain on until the room temperature increases to the temperature on the digital display. The heater will cycle on and off to maintain the desired room temperature. 6. This heater is equipped with a 12-hour automatic shut-off timer. To activate the timer, press the TIMER button on the control panel or remote control. Each press of the timer button will increase the heater operating time by one hour. The digital readout will display the number of hours you have selected. To turn off the timer, simply press the TIMER button until the digital readout displays your current selected temperature. Once you have selected a shut off time, the heater will operate for the selected time, then automatically shut off. 7. The indication lights on the control panel communicate how the heater is operating. The TIMER light will turn-on when the timer is selected. When HIGH, LOW modes are selected, the corresponding lights will turn on accordingly. 8. Unplug the heater when not in use. Temperature & Timer Display Indication Lights Receiver for Remote Control Timer Select Button Temperature Select Buttons Mode Select Button On/Off Button (Power) OPERATING INSTRUCTIONS (CONTINUED) OPTIMAL OPERATING CONDITIONS To get the most out of your Soleus Air Micathermic heater, follow these helpful hints: 1. All electric heaters are limited to maximum of 1500 watts (per UL and ET...