INSTALLATION ELECTRIC SHOCK HAZARD. Disconnect all power before installing or servicing heater. Failure to do so could result in personal injury or property damage. Heater must be installed by a qualified person in accordance with the National Electrical Code, NFPA 70. High heating efficiency, low sheath temperatures and long heater life result when electric heaters are properly installed. INSTALLATION – CLAMP-ON 1. Clamp strip heaters securely, along their entire length, to smooth metal surface

Open carton and remove heater at the place of installation. between heaters to project heat radiation downwards to maintain Mounting clamps are in parts bag in carton. comfort level within the radiation field. 2. Check nameplate volt and watt rating against your power supply voltage and heating requirements of your installation. This nameplate is located on one end of the heater. INSTALLATION MOUNTING (See Figure 1) 1. Layout heater locations to the desired heat affected work area. 2. Minimum sp

Elements Net Weight (Lbs.)1 Phase 3 Phase RBC-31280 208 1,200 5.8 —— 4,094 1 85.0 ——RBC-31220 240 2.5 ——RBC-31240 480 RBC-32480 208 2,400 11.5 —— 8,188 2 8-3/410.0 ——RBC-32420 240 5.0 ——RBC-32440 480 RBC-33680 208 3,600 17.3 10.0 12,272 3 9-3/415.0 8.7RBC-33620 240 7.5 4.3RBC-33640 480 © 2010 Chromalox, Inc. GENERAL The Chromalox Type RBC-3 Radiant Heater is designed primar-WARNING: Users should install adequate controls ily as an indoor comfort heater to be used where supplemental heat is and s

Volts kW Overall Length Heated Length RADD-2164 120 or 240 1.6 24-3/8 16-1/2RADD-2164V 208 or 275 RADD-3224 120 or 240 2.2 30-5/8 22-3/4RADD-3224V 208 or 275 RADD-3264V 208 or 275 2.6 35-7/8 28-5/16RADD-3264 240 or 480 RADD-4364V 208 or 275 3.6 46-5/8 38-1/2RADD-4364 240 or 480 RADD-5434V 208 or 275 4.3 53-7/8 45-7/16RADD-5434 240 or 480 RADD-5504V 208 or 275 5.0 61-3/8 53-3/8RADD-5504 240 or 480 RADD-6544V 208 or 275 5.4 65-7/8 58-1/4RADD-6544 240 or 480 RADD-6604V 208 or 275 6.0 73-3/4 65-3/4R

If an element or other part listed in Table A (page verting these earlier models to the current Style 3B. This conversion 3) is necessary, order according to heater housing length and the is necessary because replacement parts for the old models are no voltage and wattage stamped on the element and the heater name- longer available. plate. The changes involved are primarily in the terminal area as For complete installation information for type RAD - Style shown in Figures I, 2 and 3. Match-up on

DATESALESREFERENCEDIVISIONSECTIONChromalox® (Supersedes PG422-1)PF497-1DRA161-304812-001NOVEMBER, 20024RENEWAL PARTS IDENTIFICATIONInstallation, Operationand(Supersedes PF-497) Specifications – Table1 Portable Industrial Unit Blower Air Heater Type DRA Specifications – Table1 Portable Industrial Unit Blower Air Heater Type DRA Model Electrical Data (60 Hz) Dimensions (In.) Volts kW Phase Amps* 1/3 Ph BTU Height Width Depth DRA-07-83 208 7.5 1 and 3 36.3/21.0 25,590 34.25 27.5 25 DRA-07-23 240/20

Disconnect all power before installing or servicing heater. Failure to do so could result in personal injury or property damage. Heater must be installed by a qualified person in accordance with the National Electrical Code, NFPA 70. 1. All wiring should be done in accordance with local codes and the National Electrical Code by a qualified person. 2. Connect air heaters to same line voltage as on heater nameplate. 3. Check possibility of corrosion if heaters are operated in atmospheres other tha

K.O. Model Volts Watts Amps BTUH Length (In.) Weight (Lbs.) Stock PCN CPHH-50011 120 500 4.2 1707 17-3/8 5.0 S 350190 CPHH-50031 208 375 1.8 1280 17-3/8 5.0 S 350203 CPHH-50031 240 500 2.1 1707 17-3/8 5.0 S 350203 INSTALLATION WARNING: Hazard of Electric Shock. Disconnect all power before installing heater. WARNING: Hazard of Electric Shock. Any installation involving electric heaters must be effectively grounded in accordance with the National Electrical Code. WARNING: This heater is no

mounted to a heavy gauge metal terminal box. Due to the various options and materials available, check the IMPORTANT — Observe at least one complete heating cycle nameplate attached to the heater terminal box with the catalog operation before leaving the installation. number designation system on page 7 before installing to insure the heater you received conforms to your specification. © 2010 Chromalox, Inc. Duct Heater4 Ft. Min. Air HandlerAirFlow GENERAL Limitations: Ductwork must be in accord

© 2010 Chromalox, Inc. Type VUH Vertical Unit Heater Specifications – Table 1 Heating Capacity Volts Air Delivery Max. Dimensions (In.) Mtg. Mtg. Model Outlet Height Weight kW BTUH 1 Phase 3 Phase CFM FPM Temp. °F* (Ft.) A B C D E F H M (Lbs.) 208 VUH-C-30 30 102,000 – 240 2500 1200 96 33 18-7/8 19 34 10-5/8 15-1/4 3 11 20-3/4 250 480 VUH-C-40 38.5 136,000 – 240 2500 1200 108 30 18-7/8 19 34 10-5/8 15-1/4 3 11 20-3/4 250 39 480 VUH-C-50 50 170,000 – 480 2500 1200 120 27 18-7/8 19 34 10-5/8 15