160TH ST., CLEVELAND, OHIO 44135 E.-U. • 800-251-0001 Mr. Heater et HeatStar sont des marques de commerce deposees de enerco Group, Inc. © 2003, enerco Group Inc. Tous droits reserves. ENERCO GROUP, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 800-251-0001 08/08 #50120 4000ID Serie Chauffage Portatif Indirect-tire NO. STOCk NO. DESCRIPTION 67 e30443 Cable avec fiche et presse cable 68 e11030 Lampe 230V 69 T20353 Gicleur 1,50 GPH 45° W 70 P10137 Tete broleur avec electrodes 71 e10254 electrod
STOCk NO. 2000 3000 LEGENDE 41 I31130 • RACCoRd dRoIT O6 1/8” 42 e20953 • • EMBOUT FIXE-CABLE PG11 43 e20954 • • eMBoUT PG11 44 C30307 • • PRoT. CAoUTCHoUCH O 35 45 e50102 • • THeRMoSTAT BILAMe LIMIT 46 M20107 • • RoNdeLLe O5 X O15 X 1.5 47 e50101 • THeRMoSTAT BILAMe FAN e50104 • 48 G06132 • • GUeULARd 49 G06133 • • CoLLIeR de FIXATIoN GAINeS 50 I40801 • GAINe L=170 MM I40802 • GAINe L=170 MM 51 G06134 • • dEFLeCTeUR d’AIR 52 P50126 • • SUPPoRT CoFFReT ELECTRIQUe 53 e20508 • • PoRTe FUSIBLe 54 e
Heater read instructiOns careFullY: Read and follow all instructions. Place instructions in a safe place for future reference. Do not allow anyone who has not read these instructions to assemble, light, adjust or operate the heater. Heatstar BY enercO MoDel1000ID, 2000ID 3000ID MoDel 1000ID, 2000ID 3000ID, 4000ID indirect Fired pOrtaBle Heater if the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. warnin
Air Inlet 2.5 ft. Top 6 ft. Air outlet 12 ft. • Floors and ceilings must be made of fireproof materials in the room where the heater is operated. • The air inlet and outlet must never be blocked for any reason. • Install the heater on a flat, level floor in a steady postion. • It is forbidden to connect direct-fired heaters to air ducts. warning • DO NOT USE GASOLINE, NAPHTHA OR VOLATILE FUELS. • STOP HEATER BEFORE ADDING FUELS. • ALWAYS FILL OUTDOORS AWAY FROM OPEN FLAME • DO NOT USE EXTERNAL F
Refer to Figures 4, 5, and 7 on pages 13 and 14 for recommended suspensions. 4. GAS SUPL Y Provide adequate gas supply for rated input of each heater using American Standard Installation of gas piping and gas appliances in building ANSI/223. 1a/ NFPA54 Pamphlet, Table C-3 shows capacity of pipe of different diameters and lengths in cubic feet per hour for Natural Gas with pressure drop of 0.3 inches specify gravity of 0.60. For liquefied Petroleum Gas (LP) capacity refer to Table C-3 and C-15 of
Place instructions in a safe place for future reference. Do not allow anyone who has not read these instructions to assemble, light, adjust or operate the heater. HEATSTAR High-Intensity Infrared Heaters HS4040 HS9100S HS8060 HS9120 Mo d el s Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. WARNING :
NO. REQ’D STOCK NO. DESCRIPTION 1 1 00024 COMB. GAS VALVE (PP) NG. 1/2x1/2 NPT 2 1 00025 COMB. GAS VALVE (PP) LP. 1/2x1/2 NPT 3 1 05577 ORIFICE PILO T LP 4 1 05573 ORIFICE PILO T NG 5 1 09360 THERMOCOUPLE PP HONEYWEL 6 1 10367 THERMOSTAT “PP” HEAT STAR 7 1 11405 PILO T-PP-4K, 8K HTR NG 7 1 11408 PILO T-PP-4K, 8K HTR LP 8 1 16425 FLE X PILO T TUBE WITH FITTINGS NPP 1 4 5 6 7 8 LPP 2 3 5 6 7 8 NOTE: 1 – WHEN ORDERING SPARE PARTS ALWAYS GIVE HEATER MODEL NO., STOCK NO., SERIAL NO., AND TYPE OR GAS
NOTE : USE LATEST EDITION FOR ALL ANSI STANDARD AND CANADIAN STANDARDS. Figure 2 MODEL NO. BTU/HR. RATING GAS SUPPLY PRESSURE (W.C.) ORIFICE SIZE GAS MIN. MAX. MANIFOL D NATURAL PROPANE NAT. L.P. NAT. L.P. NAT. L.P. NAT. L.P. 4030 30,000 30,000 6.6” 11” 14” 14” 5.6” 10” 43 52 4040 40,000 40,000 6.8” 11” 14” 14” 5.8” 10” 37 49 8050 50,000 50,000 7.0” 11” 14” 14” 4.3” 10” 30 45 8060 60,000 60,000 7.0” 11” 14” 14” 5.8” 10” 29 43 8070 70,000 – 7.0” – 14” – 6.0” – 28 – 9080 80,000 80,000 7.0” 11” 14”
If thermostat, make sure selected temperature is higher than room temperature Replace control device Replace electrical motor Replace electrical motor bearings Replace condenser Motor starts, no ignition or cuts out electric ignitor defective Flame control box defective Photocell defective Not enough or no fuel at all at burner Solenoid defective Check connection of H.V. Ieads to electrodes and transformer Check electrodes setting (see scheme “GAP oF eleCTRoDeS”) Check electrodes for cleanliness
componets drawer 52 e20508 • • Fuse holder 53 e10313 • • Fuse (6x30) 20A 54 G06102 • • Switch support 55 e50437 • • Pressure switches HoNeYWell 56 e20319 • • Terminal board 57 e11125 • • Relay Finder 65.31 AC 58 e20305 • • Terminal board 59 E10917-2 • • Transformer H.T. 818C 11oV 60 G06109 • • Transformer H.T. flange 61 G06103 • • Support 62 e40107 • • LANDIS LOA 21-24 base 63 e40113 • • Control box LANDIS LOA 21-24 64 G06073 • • Plate for electrical components 65 E10102-P • • Switch 0-1 66 e206