Log:
Évaluations - 0, GPA: 0 ( )

Instructions Philips, Modèle HP6570/00

Fabricant : Philips
Taille : 742.33 kb
Nom Fichier :
Langue d'enseignement: enfr
Aller à la télécharger



Facilité d'utilisation


-If your hairs lie flat on your skin, we advise you to use the active hairlifter with active massage. The active hairlifter with active massage not only lifts up the hairs but its active massaging roller also minimises the pulling sensation of epilation. Note: Remove the basic epilation cap before you attach the optimal performance cap or the active hairlifter with active massage. 1 2 Squeeze both sides of the basic epilation cap (1) and pull it off the appliance (2) (Fig. 5). Put the desired attachment on the epilating head (Fig. 6). Note:The procedure for placing the attachments onto the appliance is the same for all attachments. 3 Press the on/off button once to switch on the epilator. The epilator starts running at speed II, which , is the most efficient speed for epilation. The bottom speed setting indication II lights up (Fig. 7). If you want to use speed I, press the on/off , button a second time.The top speed setting indication I lights up (Fig. 8). Problem Cause SolutionProblem Cause Solution Tip: Speed I is suitable for areas with little hair growth, for hard-to-reach areas and for areas where bones are located directly beneath the skin, such as knees and ankles. When you press the on/off button a third , time, the epilator switches off. 4 Stretch the skin with your free hand to make the hairs stand upright. 5 Place the epilating head at an angle of 90° onto the skin with the on/off button pointingin the direction in which you are going to move the appliance (Fig. 9). 6 - - Move the appliance slowly over the skin against the direction of hair growth. When you use the optimal performance cap, make sure that both rollers of the skin stretcher always stay in contact with the skin to ensure an optimal result. When you use the active hairlifter with active massage, make sure the active massaging roller and the active hairlifter always stay in contact with the skin.The massaging roller stimulates and relaxes the skin for a gentler epilation. Overheat protection The epilator has an integrated overheat protection, which prevents overheating of the appliance. Note:To avoid overheating of the epilator, do not press the appliance too hard onto your skin.The epilator works best when you move it over your skin without exerting any pressure. 1 2 If the overheat protection is activated, the appliance switches off automatically and the speed setting indications flash red. 3, Let the appliance cool down. The lights stop flashing after 30 seconds. When the appliance has cooled down, you can switch it on again. If the lights start to flash red again, the appliance has not yet cooled down completely. Overload protection If you press the epilating head too hard onto your skin or when the rotating tweezers of the epilating head get blocked (e.g. by clothes etc.), the appliance stops and the speed setting indications star t to flash red for 5 seconds. 1 Check if the rotating tweezers of the epilating head are blocked by turning the tweezers with your thumb until you can remove whatever is blocking the rotating tweezers. 2 Switch on the appliance again. Do not press the appliance too hard onto the skin. Cleaning and maintenance Note: Make sure the appliance is switched off and unplugged before you start to clean it. Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. - - - Clean the appliance after each use to ensure better performance. Never rinse the appliance or the adapter under the tap (Fig. 10). Keep the appliance and the adapter dr y (Fig. 11). Cleaning the attachments 1 2 3 4 Remove the attachment from the epilating head (Fig. 5). Remove loose hairs from the attachments with the cleaning brush (Fig. 12). Rinse the attachments with lukewarm water while turning them (Fig. 13). Dry the attachments before you use or store them. Cleaning the epilating head of the epilator 1 2 3 Press the release knob (1) and remove the epilating head from the appliance (2) (Fig. 14). Remove loose hairs with the cleaning brush (Fig. 15). Rinse the epilating head under the tap for 5-10 seconds while turning the tweezers with your thumb (Fig. 16). Note: Never try to detach the epilating tweezers from the epilating head. 4 5 Shake the epilating head firmly (Fig. 17). Dry the epilating head thoroughly with a tea towel. Note: Make sure the epilating head is completely dry before you place it back onto the appliance. 6 To reattach the epilating head, place it on the appliance and press it onto the appliance until it snaps home (‘click’) (Fig. 18). storage -Store the appliance and the accessories in the luxur y pouch. replacement All par ts of the appliance can be replaced. If you need to replace one or more par ts, go to your Philips dealer or an authorised Philips ser vice centre. Environment -Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to pres...

Ce manuel est également adapté pour les modèles :
Épilateurs - HP6570/10 (742.33 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories