Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
DF 1/08 ©2007 Paxar Americas, Inc. a subsidiary of LOADING LABELS & SETTING PRINT BANDS Avery Dennison Corp. All rights reserved. LOADING LABELS If labeler has no label guide: Snap Squeeze and hold If labeler has label guide: Snap label roll between hubs. Tear off operating lever half way, 12 label roll between hubs. Tear off and discard first twelve labels and and feed label strip under brake backing paper. 3 3 Continue feeding label strip until about twelve labels come out here. Release operating lever. and discard first twelve labels and wheels. backing paper. Then, insert label Brake strip into guide slot as shown. Label Guide Guide Slot Lever 4 4 a. Feed label strip up under plate until two labels come out here. separating labels from backing Plate paper. Loop Discard b. Squeeze operating separated lever halfway and rewind labels. label roll until loop is Wheel Operating 5 5 Grasp label strip and pull briskly toward operating lever, removed. Tear backing paper as Completely squeeze operating shown. lever, exposing feedwheel. 67 Straight tear between I-cuts Backing paper without labels Insert backing paper into slot. When paper bows up, maintain finger pressure and release operating lever. Slot Feedwheel 8 8 Squeeze operating lever several times until backing paper exits labeler. If backing paper does not become taut and exit at rear, remove backing paper from slot and repeat steps 6 and 7. SETTING PRINT BANDS Pull knob until indicators point to Turn knob until indicators point Set all bands and push desired band. to desired character or blank. knob in all the way. 123 • n Make sure the character you select is not a print character (UPSIDE DOWN). You should be able to read the character correctly through Indicators the band window. INKING Turn latch to release ink roll Fold a piece of scrap backing Insert folded backing paper door and carefully pull it paper. between ink roll and completely out of labeler. carrier. Pull to snap old ink roll free. 123 Ink Roll Door Latch Cut off end of new ink roll Insert ink roll into ink door Latch ink roll door securely. pouch. Using pouch to protect opening. Tilt ink door fingers, slide carrier into pouch and and press in... 456 snap new ink roll into carrier (one side at a time). Lip to place hinge tab under lip. INKING 2Rollers OPERATION 1 1 Squeeze operating lever completely. 2 2 Release operating lever completely. 3 3 Apply label to item being marked as shown. • n A wiping motion works best, DO NOT POUND labeler when applying labels. REMOVING SUPPLIES 1 1 Tear label strip and carefully remove label roll. Tear Squeeze and release operating lever until backing paper exits here. MAINTENANCE If labeler has no label guide: If labeler has label guide: To clear backing paper Remove label roll. Squeeze Remove label roll. Squeeze track, insert label removal operating lever half way and feed label operating lever half way and feed strip here, using corner to 1 2 removal strip under brake wheels... label removal strip over label guide, remove stray labels. under brake wheels... Label Guide and out the front of labeler. and out the front of labeler. Insert label removal strip here to loosen labels. Squeeze operating lever to turn feedwheel Remove ink door and inspect door opening for 3 4 for inspection. Remove stray labels with corner stray labels. Remove stray labels with corner of of label removal strip. label removal strip. Feedwheel OPERATION, REMOVING SUPPLIES & MAINTENANCE LUBRICATION TROUBLESHOOTING Monarch Lubricant 086989 is recommended. Lubricate as shown below with labeler loaded when: a. slow or hesitant feeding occurs. b. adhesive buildup is seen. c. feedwheel tears backing paper. d. ink roll is changed. LUBRICATE: One drop each side of label chute. LUBRICATE: One drop each spot on backing paper. Spread with finger. Problem Solution Labels will not feed. Reload per instructions. Check for correct supplies. Follow MAINTENANCE instructions. Check for correct print location. Print incorrectly located. Adjust per PRINT LOCATION ADJUSTMENT instructions. Printing smeared or distorted. Print several labels (15-20) until excess ink is used up. Printing too light (all over). Install new ink roll per INKING instructions. Squeeze operating lever harder during operation. Slow hesitant feeding. Labeler tends to ‘hang up’ when operating lever is released. Follow MAINTENANCE instructions. Lubricate per instructions. If none of the above eliminates the problem, return DO labeler to an Authorized Paxar Service Center. NOT OVER LUBRICATE! PRINT LOCATION ADJUSTMENT AVAILABLE SUPPLIES Print location is correct when 000940 Holster (Vinyl) all characters are fully visible on 000935 Label Scraper the printed label. Dial characters (w/ handle, Pkg of 20) for every position when testing M00PLS01 Label Scraper location. (w/o handle Pkg of 10) 119919 Maintenance Kit 1 1 Place small coin in slot of each 08394601 Black Ink Roll disk (one on each side of labeler) as shown. 2 2 Hold coin stea...