Évaluations - , GPA: ( )

Instructions Desa, Modèle (V)K36N SERIES

Fabricant : Desa
Taille : 2.55 mb
Nom Fichier : 8230dc1d-0933-1fe4-8978-0c6abf0f371e.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Remove battery cover on back of remote control unit. 2. Attach terminal wires to a 9-volt alkaline battery (not included). Place battery into the battery housing. 3. Replace battery cover onto remote control unit. Remote Control Unit Terminal Wires 9-Volt Alkaline Battery Battery Cover Battery Housing Figure 39 - Installing Alkaline Battery in Hand-Held Remote Control Unit (GHRCB) Terminal 9-Volt Battery Remote Control Unit Battery Cover Wires Figure 40- Installing Battery in Hand-Held Remote Control Unit (GHRCTBSeries) REMOVING/REPLACING GLASS DOOR CAUTION: Do not operate this fireplace with a broken glass door panel or without the glass door panel securely in place. For replacement part information see Replacement Parts, page 31. Removing Louver Panels Remove the top and bottom louver panels by simultaneously pulling both top end spring latches towards the center of the appliance until they are disengaged from the locating holes (see Figure 41). Repeat for bottom spring latches and pull the louvers outward. To install or replace items removed, simply reverse the procedures above. Louver Panel Figure 41 - Removing Louver Panel Spring Latch CAUTION: Wear gloves and safety glasses while handling or removing broken glass. Do not remove if glass is hot. Keep children and pets away from glass. WARNING: If fireplace has been running, turn off and unplug fireplace. Let cool before removing glass door or louvers. For more information, visit more information, visit 111923-01B 111923-01B Forr morre iinfforrmattiion,, viisiitt 22 Unlock Lock Glass Frame Assembly Screw Figure 42 - Removing/Replacing Glass Door INSTALLING BRICK LINER MODELS BL36DA(SA) AND BL36DHA(SA) WARNING: If fireplace has been running, turn off unit. Let cool before installing brick liner. You may purchase brick liner from your local retailer or see Accessories, page 36. CAUTION: Always handle brick panels with two hands. Do not force brick panels into place. Excessive force will break brick panels. 1. Remove top and bottom louvers to allow access to door latches. 2. Unlock door latches and open glass door. See Removing/Replacing Glass Door, steps 1 and 2. 3. If installing brick liner in new fireplace, go to step 4. If installing brick liner in an existing fireplace, carefully remove logs, lava rock, and ember material. 4. Remove three screws from deflector shield on the inside top of firebox. Set shield and screws aside. 5. Install rear brick panel first. Rest bottom edge of panel on back edge of burner assembly (see Figure 43). 6. Install left side brick panel by sliding it between the burner assembly and the side of the firebox (see Figure 43). 7. Install the right brick panel using the same method described 8. Replace deflector shield using screws removed in step 4. 9. Follow instructions to install logs, lava rock, and ember material. 10. Close glass door and lock latches on top and bottom of door and replace screen. See Removing/Replacing Glass Door, steps 5 and 6. 11. Close top and bottom louvers. Hinge Removing Glass Doors If replacement of glass is necessary, the entire assembly, glass and frame, must be replaced. If glass is broken, wear gloves and tape the remaining fragments onto the frame. 1. Remove screen assembly by pushing the rod either left or right and then down and forward to remove screen/rod assembly from the firebox. Set assembly aside. 2. Lift up on latches to unlock. There are two on top of firebox and two below firebox that hold glass door in place (see Figure 42). 3. While holding glass door to prevent it from falling and causing injury, remove the five screws from the hinge located on the left side of door frame assembly (see Figure 42). 4. Remount the new frame at the hinge with five new screws before closing door. This will ensure seating of the gasket. 5. Close glass door frame. Lock latches by placing the bar under the tab on door and pushing down and back on latch (see Figure 42). 6. Replace screen/rod assembly by reversing step 1. 7. Replace louvers by reversing procedure under Removing Louver Panels, page 21. Cleaning Glass Door See Cleaning and Maintenance on page 27. Latch FIREPLACE INSTALLATION Continued FIREPLACE INSTALLATION Removing/Replacing Glass Door (Cont.) Installing Optional Brick Liner Models BL36D(S) and BL36DH(S) Figure 43 - Installing Rear Brick Panel Rear Brick Panel Left Side Brick Panel 111923-01B Forr morre iinfforrmattiion,, viisiitt 2233 FIREPLACE INSTALLATION Continued FIREPLACE INSTALLATION Installing Logs, Lava Rock and Glowing Embers OPERATING FIREPLACE For Your Safety Read Before Lighting Figure 47 - Installing Log No. 7 INSTALLING LOGS, LAVA ROCK AND GLOWING EMBERS Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with fireplace. Open louvers, remove screen, ...