Évaluations - , GPA: ( )

Instructions Desa Tech, Modèle S26PTA

Fabricant : Desa Tech
Taille : 691.08 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

7. Attach the two mounting brackets to blower housing using four screws provided in blower kit (2 for each bracket) (see Figure 16, page 13). Tighten screws securely. Place blower assembly temporarily on top of firebox. 8. Working from the rear of the stove, place entire power cord, including speed control housing, in lower control compartment. 9. Route ends of 3-wire power cord up from the lower control compartment through the plastic bushing, then up to the upper cavity of stove (see Figure 17, page 13). 10. Attach the terminal ends of the white and black power cord wires to the terminals on the blower motor (see Figure 14). Push firmly. 11. Attach the terminal end of the green power cord wire to the front tab of the blower housing using screw provided (see Figure 14). Figure 13 - Removing Stove Top Panel Figure 14 - Removing Wires from Blower Figure 15 - Installing Bushing Screw Green Ground Wire White Powercord Wire Black Powercord Wire Bushing 110361-01E 13 INSTALLATION Continued Figure 16 - Removing Blower Brackets from Stove and Attaching to Blower Blower Blower Bracket Firebox Top 12. Using the four screws previously removed, mount blower assembly to stove by reattaching blower brackets to rear panel (see Figure 16). Tighten screws securely. 13. Install plastic control knob onto output shaft of speed control housing (see Figure 17). Place speed control housing just inside control compartment door in front of stove (see Figure 17). 14. Using two screws provided in blower kit, mount blower speed control housing to mounting tab in left side of lower control compartment (see Figure 18). 15. Check to make sure that the power cord is completely clear of blower wheel and there are no foreign objects in blower wheel. 16. Carefully replace stove top panel. Align holes and replace six screws removed in step 1, page 12. 17. Peel off the backing paper and stick the supplied wiring diagram decal on the stove floor as shown in Figure 18. 18. Plug power cord into a convenient 3-prong grounded wall receptacle near the stove. WARNING: Electrical Grounding Instructions:This appliance is equipped with a threeprong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded threeprong receptacle. 19. Using speed control knob, turn blower on and check for operation. 20. All remaining parts from blower kit may be discarded. Figure 17 - Installing Blower Control Housing Power Cord Speed Control Housing Control Knob Figure 18 - Routing Power Cord Blower Speed Control Housing Wiring Diagram Decal 120 Vac. 60 Hz. . 78 Amps Variable Fan Switch White White Black Green On 110/115 V.A.C. Blower Motor Black Black Black Off WARNING: Never attempt to service heater while it is plugged in, operating, or hot. Burns and electrical shock could result. Only a qualified service person should service or repair heater. If any of the original wire as supplied with the appliance must be replaced, it must be replaced with 105°C wire or it’s equivalent. WARNING: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. DESA Heating Products, Bowling Green, KY OPERATING HEATER FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. LIGHTING INSTRUCTIONS NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange flame will also be present. Open a window to vent smell. This will only last a few hours. 1. STOP! Read the safety information, above. 2. Make sure equipment shutoff valve is fully open. 3. Turn control knob clockwise to the OFF position. 4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the fl...