Évaluations - 3, GPA: 4.7 ( )

Fabricant : Lennox Hearth Taille : 4.36 mb Nom Fichier : Langue d'enseignement:

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Observe the individual tongues of flame on the burner. Make sure all ports are open and producing flame evenly across the burner. If any ports are blocked, or partially blocked, clean out the ports. SIT Gas Valve Shown with control compartment door removed Piezo Igniter HoneywellGas Valve Sit and Honeywell Millivolt Gas Valve Showing Piezo Igniter Location (Each Unit is Equipped with Only One of these Gas Valves) Figure 50 Replacelogsifremovedforpilotinspection. Tolighttheburner;turn“ON”theremotewallswitchandrotatethegasvalvecontrolknobcounterclockwisetothe“ON”position. Figure 51 Thermocouple Thermopile Pilot Nozzels SIT MILLIVOLT PILOT ASSEMBLY Igniter Rod Hood Proper Pilot Flame Appearance 3/8" Min. (9 mm) Figure 52 Proper Pilot Flame Appearance Thermocouple Thermopile Pilot Nozzels 1/8" Min. (3 mm) Igniter Rod Hood HONEYWELL MILLIVOLT PILOT ASSEMBLY 3/8" Min. (9 mm) Electronic Appliance Checkout Tolighttheburner,turn‘ON’theoptionalremote wall switch and turn the gas control switch to the “ON” position. Ensure the Igniter lights the pilot. The pilot flame should engulf the flame rod as shown in Figure 53. Figure 53 3/8" to 1/2" (9 -13 mm) Ground Electrode Flame Rod Hot Surface Igniter Proper Flame Adjustment Pilot Nozzels ELECTRONIC PILOT ASSEMBLY Proper Pilot Flame Appearance Step 8. INSTALL VERMICULITE, VOLCANIC STONE, GLOWING EMBERS AND LOGS 1. Remove the front glass enclosure panel (see Removing Glass Enclosure Panels on Page 31). 2. Remove log set box from firebox. Next, remove embers and vermiculite from control compartment. Handlelogscarefullytoprevent breakage. 3. Install Vermiculite -Placesome vermiculite on the firebox floor around the burner (the entire bag of vermiculite will NOT be used). See Figures 55 & 56. DO NOT PLACE ANY VERMICULITE ON THE BURNER. Mound up a portion of the vermiculite in front of the burner. 4. Install decorative volcanic stone -Sprinkle the decorative volcanic stone (dark colored) on top of the vermiculite (light colored) in a pleasing pattern (see Figures 55 & 56). 5. Placement of Glowing Embers - Separate the Embers (rockwool) into pieces about the size of a quarter (see Figure 54). Keep the pieces fluffed up, not matted. Distribute these pieces over the surface of the burner, as shown in Figures 55 & 56. Do not use more than is necessary. Ensure that the main burner slots remain uncovered by the ember material. Note: This appliance is provided with enough Glowing Embers for several applications, do not use all that is in a new bag at one time. For best glowing effect, replace the ember material annually. 6. Placement of Logs and Twigs - Alllogsthathavelocatingnotchesorslotstohelp ensure that they are properly positioned. All top logs that rest on lower logs, do so over notches, indents or pins. Proper twig placement is critical to prevent sooting. Twigs should be placed in the gaps between the flame peaks and should be positioned so they do not impinge the flames. LMDV-3328 & LMDV-3530 -Install as Follows Carefullypositiontheceramicfiberlogsandtwigs over the burner as shown in Figure 55. Logs should be placed in the order shown and per the following instructions. 1. Place the rear log (A) as shown. Position the 2 notches on the bottom of the log over the 2 corresponding locating brackets against the back wall of firebox. 2. Place the left log (B) as shown. The notch on the bottom of the log should fit over the corresponding locating bracket. 3. Place the right log (E) as shown. The hole on the back of the log should fit over the corresponding pin on the rear log (A). Make sure that the log is positioned so it aligns to the sides of the gas ports on the corner of the burner. 4. Place the left center log (C) as shown. The forked end of the log fits into the corresponding notch on rear log (A). The slot on the other end (bottom) of log fits over the corresponding locating bracket on the sub-floor. 5. Place the right center log (D) as shown. One end of the log fits into the corresponding indent on the right log (E). The slot on the other end (bottom) of log fits over the corresponding locating bracket on the sub-floor. LMDV-4035 -Install as Follows Carefullypositiontheceramicfiberlogsandtwigs over the burner as shown in Figure 56. Logs should be placed in the order shown and per the following instructions. 1. Position the center log (C) onto the 2 corresponding location pins on the burner. 2. Place the rear log (A) as shown. Position the 2 notches on the bottom of the log over the 2 corresponding locating brackets against the back wall of firebox. 3. Place the left log (B) as shown. The notch on the bottom of the log should fit over the corresponding locating bracket. 4. Place the right log (E) as shown. The notch on the bottom of the log should fit over the correspondinglocatingbracket.Makesure that the log is positioned so it aligns to the sides of the gas ports on the corner of the burner. 5. Place the center front log ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :