Évaluations - 5, GPA: 3.6 ( )

Fabricant : Lennox Hearth Taille : 3.72 mb Nom Fichier : Langue d'enseignement:

Remove any surface build-up on pilot and burner assembly. Wipe the pilot nozzles, ignitor/flame rod and hood. Ensure the pilot flame engulfs the flame sensor as shown. Inspect the vent system at the top and at the base (within the firebox) for signs of blockage or obstruction. Look for any signs of dislocation of the vent components. Perform the appropriate appliance checkout procedure detailed in this manual. Remove old ember materials and vacuum the rockwool placement area. Place new rockwool as described in this document. Maintenance Schedule Annually (Before the onset of the Burning Season) Periodically (After the Burning Season) Maintenance Task Accomplishing Person Procedure Cleaning Firebox Interior Check Flame Patterns and Flame Height Checking Vent System Cleaning Front Glass Enclosure Panel Homeowner Homeowner Homeowner Homeowner Carefully remove logs, rockwool and decorative volcanic stone and vermiculite. Vacuum out interior of the firebox. Clean firebox walls and log grate. Replace logs, Rockwool and volcanic stone as detailed in this manual. Clean as necessary following the directions provided in this manual. DO NOT TOUCH OR ATTEMPT TO CLEAN GLASS WHILE HOT. Inspect the vent system at the top and at the base (within the firebox) for signs of blockage or obstruction. Look for any signs of dislocation of the vent components. Refer to Refer to Figures 6 (EDV3530), 7 (EDV4035) or 8 (EDV4540) on page 7 and verify the flame pattern and height displayed by the appliance conforms to the picture. Flames must not impinge on the logs. Figure 4 Glass Door Latch Lower Compartment Door and Hinge Glass Door Firebox Floor Bottom Vee-flange Glass Door Frame Top Flange Glass Door Frame Modesty Panel To install the front glass enclosure panel, proceed as follows: Glass Door Latch Lower Compartment Door and Hinge Glass Door Firebox Floor Bottom Vee-flange Glass Door Frame Top Flange Glass Door Frame Modesty Panel To install the front glass enclosure panel, proceed as follows: 1. Retrieve the glass door frame. Visually inspect the gasket on the backside of the panel. The gasket surface must be clean, free of irregularities and seated firmly. 2. Position the door frame in front of the firebox opening and engage the top flange over the lip at the top of the firebox opening. 3. Swing the door down and back. Ensure the gasket seats evenly as the door draws shut. Engage the Vee-flange at the bottom of the door with the latches and close the latches to secure the door. 4. Reinstall the bottom compartment door by inserting the right side locating pin into the right cabinet corner post and then the left side spring- loaded pin into the left cabinet corner post. 5. Reinstall the top and bottom bustle, and the top louver assembly or radiant panel. Burner Adjustments The following paragraphs address burner adjustment concerns and procedures. Flame Appearance and Sooting Proper flame appearance is a matter of taste. Generally most people prefer the warm glow of a yellow to orange flame. Appliances operated with air shutter openings that are too large will exhibit flames that are blue and transparent. These weak, blue and transparent flames are termed anemic. If the air shutter opening is too small sooting may develop. Sooting is indicated by black puffs developing at the tips of very long orange flames. Sooting results in black deposits forming on the logs, appliance inside surfaces and on exterior surfaces adjacent to the vent termination. Sooting is caused by incomplete combustion in the flames and a lack of combustion air entering the air shutter opening. To achieve a warm yellow to orange flame with an orange body that does not soot, the shutter opening must be adjusted between these two extremes. No smoke or soot should be present. Reposition the logs if the flames impinge on any of them. If the logs are properly positioned and sooting conditions exist, the air shutter opening on the main burner tube should be adjusted. Normally, the more offsets in the vent system, the greater the need for the air shutter to be opened further. WARNING: AIR SHUTTER ADJUSTMENT SHOULD ONLY BE PERFORMED BY A QUALIFIED PROFESSIONAL SERVICE TECHNICIAN. ENSURE THAT THE FRONT GLASS PANEL IS IN PLACE AND SEALED DURING ADJUSTMENT. Adjustment CAUTION: THE ADJUSTMENT ROD AND NEARBY APPLIANCE SURFACES ARE HOT. EXERCISE CAUTION TO AVOID INJURY WHILE ADJUSTING FLAME APPEARANCE. To adjust the flame, move the adjustment rod (located in the lower control area) back or forward to increase or reduce the air shutter opening, respectively. Position the air shutter to the factory setting as shown in Figure 5 on page 7. Allow the burner to operate for at least 15 minutes. Observe the flame continuously. If it appears weak or sooty as previously described, adjust the air shutter by pushing or pulling on the adjustment rod until the flame appearance is as desired. The adjustment rod and associated adjustable air shutter is patented technology. Flame adjustments ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :