Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
This will reduce the velocity of the exhaust gases, slowing down the fl ame pattern and creating a more traditional gentle appearance. Specifi c instructions are included with the kit. 10.3 FLAME CHARACTERISTICS It’s important to periodically perform a visual check of the pilot and burner fl ames. Compare them to the illustrations provided. If any fl ames appear abnormal call a service person. PILOT 3/8” - 1/2” BURNER FLAME MUST ENVELOP UPPER 3/8” TO 1/2” OF FLAME SENSOR FLAME SENSOR ELECTRODE 54.1 GDS60 NG 3/8” LP 5/16” FIGURE 10.1 FIGURE 10.2 FIGURE 10.3a FIGURE 10.3b 11.0 MAINTENANCE TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE. ! WARNING APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE HAS COOLED. DO NOT USE ABRASIVE CLEANERS. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. This appliance and its venting system should be inspected before use and at least annually by a qualified service person. The appliance area must be kept clear and free of combustible materials, gasoline or other flammable vapours and liquids. The flow of combustion and ventilation air must not be obstructed. 1. In order to properly clean the burner and pilot assembly, remove the logs exposing both assemblies. 2. Keep the control compartment, logs, burner, air shutter opening and the area surrounding the logs clean by vacuuming or brushing, at least once a year. 3. Check to see that all burner ports are burning. Clean out any of the ports which may not be burning or are not burning properly. 4. Check to see that the pilot flames are large enough to engulf the thermocouple and the thermopile on one leg and reaches toward the burner on the other leg. 5. Replace the cleaned logs. 6. Check to see that the main burner ignites completely on all openings when the gas knob for the burner is turned on. A 5-10 second total light-up period is satisfactory. If ignition takes longer, consult your Napoleon® dealer/distributor. 7. Check that the door gasketing is not broken or missing. Replace if necessary. W415-0788 / A / 09.22.09 12.0 REPLACEMENTS Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Authorized dealer / distributor. FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM. When ordering replacement parts always give the following information: ! WARNING • Model & Serial Number of appliance FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS • Installation date of appliance MANUAL OR FAILURE TO USE ONLY • Part number PARTS SPECIFICALLY APPROVED • Description of part WITH THIS APPLIANCE MAY • Finish RESULT IN PROPERTY DAMAGE OR * IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR PERSONAL INJURY. FURTHER INFORMATION, CONTACT YOUR AUTHORIZED DEALER. 41.1 COMMON COMPONENTS REF NO. PART NO. DESCRIPTION 1 W135-0209 LOG #1 2 W135-0082 CHARCOAL PIECE (LOG #2) 3 W135-0182 LOG #3 4 W135-0210 LOG #4 5 W135-0211 LOG #5 6 W135-0212 LOG #6 7 W135-0213 LOG #7 8 GL-646 LOG SET 9 W725-0062 SIT VALVE - NG 9 W725-0063 SIT VALVE - LP 10 W010-0624 BURNER 11 W455-0058 #35 BURNER ORIFICE - NG 11 W455-0059 #53 BURNER ORIFICE - LP 11 W455-0065 #45 BURNER ORIFICE - NG 11 W455-0050 #55 BURNER ORIFICE - LP 12 W010-1865 PILOT ASSEMBLY - NG 12 W010-1866 PILOT ASSEMBLY - LP 13 W455-0069 PILOT INJECTOR - NG 13 W455-0068 PILOT INJECTOR - LP 14* W190-0029 IPI BOARD 15* W707-0010 TRANSFORMER 16* W361-0016 GLOWING EMBERS 17* W550-0001 CHARCOAL EMBERS 19* W385-0334 NAPOLEON® LOGO 20 W390-0001 LATCH 21* W660-0009 ON/OFF SWITCH 22* W690-0002 THERMODISC 23* W380-0002 VARIABLE SPEED SWITCH KNOB 24 KB-35 VARIABLE SPEED SWITCH 25 GZ-552 REPLACEMENT BLOWER W415-0788 / A / 09.22.09 COMMON COMPONENTS REF NO. PART NO. DESCRIPTION 26 W135-0377** SIDE (LEFT OR RIGHT) 27 W135-0375** TOP 28 W135-0376** FRONT 29* W010-0648 GLASS WITH GASKET 30* W190-0029 CONTROL MODULE - EI **FOR OTHER AVAILABLE COLOURS, ADD THESE LETTERS TO THE BASE PART NUMBER: COLOR LETTER FINISH MAJOLICA BROWN N PORCELAIN GS60 COMPONENTS REF NO. PART NO. DESCRIPTION 31 W010-0459 ADAPTOR C/W SPILL SWITCH 32 W660-0006 SPILL SWITCH 33 W080-0405 SPILL SWITCH BRACKET TERMINAL KITS REF NO. PART NO. DESCRIPTION GD-175 WALL TERMINAL KIT 34 BM6790 90° ELBOW - 7" DIAMETER 35 GD-222 TERMINAL ASSEMBLY 36 BM67ADJ 30" TO 53" ADJUSTABLE PIPE - 7" DIA 37 W010-1313 FIRESTOP SPACER 38* W585-0267 TOP VENT SHIELD 39* W020-0032 HARDWARE 40 BM3730 BLACK TRIM COLLAR 41 BM6724 24" STOVE PIPE - 7" DIAMETER 42* W010-0300 10' ALUMINUM FLEX LINER C/W SPACERS - 4" DIA 43* W025-0003 DECORATIVE BLACK BAND GD-180 PERISCOPE TERMINAL KIT 34 BM6790 90° ELBOW - 7" DIAMETER 36 BM67ADJ 30" TO 53" ADJUSTABLE PIPE - 7" DIA 37 W010-1313 FIRESTOP SPACER 38* W585-0267 TOP VENT SHIELD 39* W020-0032 HARDWARE 40 BM3730 BLACK TRIM COLLAR 41 BM6724 24" STOVE PIPE - 7" D...