Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Insulation may then be installed above sheeting material to assure the space around the fireplace is totally protected. (Fig. 5) CAUTION: WHEN INSTALLING A FIREPLACE IN AN INSULATED ENCLOSURE, BE SURE ALL RE- QUIRED AIR SPACES ARE MAINTAINED. (Page 15, Fig. 19) vertical chimney heights less than 30 feet above the hearth. Chimney supports are required if the vertical height exceeds 30 feet with 11CF chimneys. Locate chimney supports at ceiling holes or other structural framing at 30 foot heights. Spacing between chimney supports must not exceed 30 feet. Use Chimney Support Model 11CS. (NOTE: The 11CS can not be mounted directly to the fireplace.) Support provided by elbow straps fulfills the support requirement only if they are spaced as previously described. (A chimney support is 2..." long when installed.) Angled chimney runs require a support every six (6) feet in addition to the elbow straps. Chimney supports are used for this function. (Fig. 9) Chase Installation A chase is a vertical boxlike structure which encloses the fireplace and/or chimney. Chases are typically built on the outside of the house with fireplace opening cut into the outer wall of a room. (Page 5, Fig. 5) If you need help in determining fireplace location or how the chimney system should be run, contact your Majestic Fireplaces dealer for assistance. FP284 Chimney Support Strap 11CS Fig. 9 Chimney support installation SHR Series Woodburning Fireplaces Framing FP555SHR Hard, Flat Surface Insulation Platform Fig. 10 Insulating between platform and fireplace. Framing can be constructed before or after the fireplace is set in place, however, most installers build the frame before setting the fireplace. Frame fireplace with 2 x 4 lumber or heavier materials. Refer to framing dimensions in Figures 1 - 4 for basic fireplace specifications. NOTE: Framing should be positioned to accommodate wall covering and fireplace facing material. Firebrick Installation For the SHR52 model the firebrick is packed separately and must be installed in the fireplace. You will need four (4) firebrick, three (3) brick retainers, a phillips head screwdriver, and the grate. The side and rear firebrick each have a notch in the top of the brick panel. The side firebrick have a notch in the lower front side of each panel. The herringbone pattern faces out of the fireplace always. (Fig. 11) NOTE: The screens and screen rod smoke baffle assembly must be removed and set aside before proceeding. Remove the two screws holding the screens place. There are seven screws holding the screen rod smoke baffle in place. 1. Remove the three brick retainers from the combustion dome by removing the phillips screws, set aside. 2. Set the left firebrick in place on the left side of the fireplace. Rear Firebrick Brick Retainer Side Firebrick Front Notch FP1234 Fig. 11 SHR52 Firebrick installation. 3. Slide the rear firebrick back into the left corner behind the end of the left firebrick. Push both panels back as far as possible into the left side and corner. 4. Swing the right side of the back firebrick into place. Attach the left brick in place using a brick retainer at the top and phillips screw removed earlier. 5. Slide the right firebrick into place as far back as possible. Attach rear firebrick and right firebrick using brick retainers and phillips screws removed earlier. 6. Slide the hearth firebrick into the grate clip. (Fig. 12) The grate will be used as a handle to set the hearth firebrick in place. 7. With the hearth firebrick securely in place in the grate clip, carefully lift the hearth firebrick into the fireplace, set the rear of the firebrick down, then slide back to meet the rear firebrick. Gently set the front of the firebrick in place. Replace screens and screen rod smoke baffle assembly. Grate Grate Clip Hearth Firebrick FP1235 Fig. 12 Hearth firebrick in place in grate clip. Chimney Set-up Since you have already preplanned the chimney run, you should know exactly how the installation is to be accomplished — how much pipe is required, the number of elbows, if any, and type of termination to be used. SHR Series Woodburning Fireplace CAUTION: REPORT TO YOUR DEALER ANY PARTS DAMAGED IN SHIPMENT, SPECIFICALLY CHECK THE END CONNECTION OF CHIMNEY SECTIONS AND ELBOWS. NOTE: SHR Series Fireplaces must use CFM Corporation model 11CF, 11 inch, 2 wall chimney systems. The installation procedure described in this manual applies only to the 11CF system, chimney components may not be mixed. Straight-Up Chimney Installation To mark the centerline of the flue, put the fireplace in final position and measure out from the wall 11...". Mark a spot on the ceiling directly above the fireplace. Draw a line parallel to the back wall through this mark. (Fig. 13) Using a plumb bob positioned directly over center point of fireplace flue collar, mark the ceiling to establish the chimney center point. (Fig. 13) Offset Installation In order to clear an obstruction, it may be necessary to offset ...
Ce manuel est également adapté pour les modèles :Cheminées - SHR36 (1.39 mb)
Cheminées - SHR48 (1.39 mb)
Cheminées - SHR52 (1.39 mb)