Log:
Évaluations - 1, GPA: 5 ( )

Instructions Greenway Home Products, Modèle Electric Fireplace Mantel MEF2511OK

Fabricant : Greenway Home Products
Taille : 778.34 kb
Nom Fichier : 7ca0550c-ccc4-4291-ac60-ca2bb632740a.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Be sure you have all the parts and can identify them. • A helping hand is always good. Assemble your mantel with an adult assistant if possible. Some pieces are heavy and will need to be held by a helper. Assembly time will take approximately 30-60 minutes. 118 320 638 1092 RIGHT SIDE BASE FRONT PANEL CENTRAL HEADER LEFT SIDE PANEL TOP WING NUT(5*28) 23PCS UPPER FACING TOP 1PC OAK: ZZ.2511OK.07 BASE 1PC OAK: ZZ.2511OK.01 CENTRAL HEADER 1PC OAK: ZZ.2511OK.06 Upper facing PANEL 1PC OAK: ZZ.2511OK.08 LEFT front panel 1PC OAK: ZZ.2511OK.05 118 1016 320 RIGHT SIDE PANEL BASE CENTRAL HEADER LEFT SIDE PANEL 2PC WING NUT(5*28) 23PCS UPPER FACING RIGHT SIDE PANEL LEFT FRONT PANEL 2PC 2PC 23PCS INSIDE VIEW 118 1016 320 RIGHT SIDE PANEL BASE CENTRAL HEADER LEFT SIDE PANEL 2PC WING NUT(5*28) 23PCS UPPER FACING RIGHT FRONT PANEL TOP 4PCS OUTSIDE VIEW LEFT side panel 1PC OAK: ZZ.2511OK.03 RIGHT front panel 1PC OAK: ZZ.2511OK.04 RIGHT side panel 1PC OAK: ZZ.2511OK.02 WINGNUT AND LOCK WASHER ANTI-TIP DEVICE 2 SETS Includes 1 spare 22PCS 22PCS 2PCS 2PCS 4PCS 4PCS 4PCS 118 1016 320 4 5 6 1 1 1 7 UPPER FACING 1 8 1 1143 638 471 1092 60 CENTRAL HEADER RIGHT FRONT PANEL LEFT FRONT PANEL TOP RIGHT SIDE PANEL BASE RIGHT FRONT PANEL CENTRAL HEADER LEFT SIDE PANEL TOP 2PC 4PCS FLAT HEAD SCREW(4*16mm)4PCS FLAT HEAD SCREW(4*30mm)4PCS WING NUT(5*28) 23PCS UPPER FACING 381 118 1016 320 1 2 3 4 5 6 1 1 1 1 1 1 MODEL MEF2511OK ITEM NAME PART NO. MANTEL PART NAME QTY. 7 UPPER FACING 1 8 1 471 60 RIGHT SIDE PANEL BASE CENTRAL HEADER RIGHT FRONT PANEL LEFT SIDE PANEL LEFT FRONT PANEL TOP RIGHT SIDE PANEL BASE CENTRAL HEADER LEFT SIDE PANEL LEFT FRONT PANEL 2PC 2PC WING NUT(5*28) 23PCS UPPER FACING 118 320 1092 RIGHT SIDE PANEL BASE CENTRAL HEADER LEFT SIDE PANEL 2PC WING NUT(5*28) 23PCS UPPER FACING 1 Get Ready to Start Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or exacto-knife as you may cut into the mantel pieces inside the box and damage the finish. Check for the hardware bag which is RED and located inside the packaging, taped to the top box. Be sure you DO NOT discard any pieces. Step 1 Locate the base and place it on the floor. Do not put it up against the wall at this point in the assembly, as you need to get in behind the mantel to insert several wingnuts, lock washers and firebox screws. Step 2 Locate the left side panel and the left front panel. Facing the front of the base, take the left side panel, positioning it so the holes in the blocks on the bottom line up with the holes on the base. Position the left front panel next to the left side panel, lining up the holes in the blocks with the holes on the base. Attach the left front and side panel to the base by inserting and tightening 1 wingnut and 1 lock washer to each piece. Attach the left side and front panels together by inserting and tightening 3 wingnuts and 3 lock washers onto the blocks. Step 3 Repeat Step 2, but with the right side panel and the right front panel. Step 4 Locate the upper facing panel. Position the panel with the finished side facing the front of the mantel. Attach to the right and left legs by lining up the holes on each side inserting and tightening 1 wing nut and 1 lock washer on each side. Locate the central header that will be attached to the left and right legs and will sit above the upper facing panel. Position this panel with the finished side facing the front of the mantel. Line up the holes on each side and insert and tighten 2 wingnuts and 2 lock washers on each side. Step 5 Get your assistant and locate the top of your mantel. This top is very heavy. It will take 2 people to lift and position it in place. Ensure the top goes over the positioning guide located on the header. The top must go over this guide to be positioned correctly. Line up the holes on the top of the mantel, insert and tighten 5 wing nuts and lock washers. 1 2 3 4 5 6 1 1 1 1 1 1 MODEL MEF2511OK ITEM NAME PART NO. MANTEL PART NAME QTY. 7 UPPER FACING 1 8 1 RIGHT SIDE PANEL BASE CENTRAL HEADER RIGHT FRONT PANEL LEFT SIDE PANEL LEFT FRONT PANEL TOP RIGHT SIDE PANEL LEFT SIDE PANEL 1 1 1 1 1 1 MEF2511OK MANTEL PART NAME QTY. UPPER FACING 1 1 RIGHT SIDE PANEL BASE CENTRAL HEADER RIGHT FRONT PANEL LEFT SIDE PANEL LEFT FRONT PANEL TOP BASE RIGHT FRONT PANEL CENTRAL HEADER LEFT SIDE TOP 4PCS FLAT HEAD SCREW(4*16mm)4PCS UPPER FACING Step 1 Step 4 Step 5 381 118 1016 320 1 2 3 4 5 6 1 1 1 1 1 1 MODEL MEF2511OK ITEM NAME PART NO. MANTEL PART NAME QTY. 7 UPPER FACING 1 8 1 60 RIGHT SIDE PANEL BASE CENTRAL HEADER RIGHT FRONT PANEL LEFT SIDE PANEL LEFT FRONT PANEL TOP RIGHT SIDE PANEL BASE LEFT SIDE PANEL LEFT FRONT PANEL Step 2 & 3 2 step 6 Take your electric firebox out of its packaging and position it between the 2 legs of the mantel. Once you are close to the wall, plug the firebox into the nearest outlet. step 6 Takeyourelectricfireboxoutofitspackagingandpositionitbetweenthe2legsofthemantel.Onceyouareclosetothewall,plugthefireboxinto...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories