Évaluations - 5, GPA: 3.8
(
)
)
|
Facilité d'utilisation
This fireplace was not tested and listed for use with an unvented gas log heater. Do not install an unvented gas log heater in this fireplace and operate it with the flue damper in the closed position unless the unvented gas log heater has been specifically tested and listed for use in this fireplace by Underwriters Laboratories Inc. Use of an unvented gas log heater in this factory built fireplace may create a fire hazard that can result in a structure fire. • Maximum input is 100,000 BTU/hr. • Decorative gas appliance must be certified to ANSI Z21.60 “Standard for Decorative Gas Appliances for Installation WARNING Asphyxiation Risk • Damper must be locked open when gas logs installed. Gas fire generates fumes. WARNING Fire Risk • For use with solid wood fuel or decorative gas appliance only. • DO NOT install unvented gas logs. WARNING Fire Risk Explosion Risk Inspect appliance and components for damage. Damaged parts may impair safe operation. • Do NOT install damaged components. • Do NOT install incomplete components. • Do NOT install substitute components Report damaged parts to dealer. in Vented Fireplaces”. • Must be installed in accordance with the National Fuel Gas Code, ANSI Z223.1. • A log set must incorporate a gas shutoff. • Log set requires the damper to be locked fully open. Knockouts are provided on both sides of the fireplace and in refractories for 1/2 in. (13 mm) iron pipe. • We recommend you seal refractory around pipe with fireplace mortar or high temperature, noncombustible sealant. • Repack insulation from the knockout around the pipe. • Maintain 1-1/2 in. (38 mm) air space around the pipe for 4 in. (102 mm) beyond the fireplace. • See Figure 7.1. Outer shell of fireplace Firebox Maintain air clearance to combustibles. Repack insulation knockout Gas line Gas line Refractory Seal with fireplace mortar or non-combustible sealant 4 in. Combustible materials 1 1/2 in. (38 mm) air space around pipe Combustible materials may be located at zero clearance to gas line beyond 4 in. (102 mm) from fireplace side. (102 mm) Figure 7.1 Gas Line Installation Outdoor Lifestyles by Hearth & Home Technologies Inc. • Montana US-CAN • 4039-156 Rev P • 10/12 Outdoor Lifestyles by Hearth & Home Technologies Inc. • Montana US-CAN • 4039-156 Rev P• 10/12 23 8 Finishing A. Hearth Extension A hearth extension must be installed with all fireplaces to protect the combustible floor in front of the fireplace from both radiant heat and sparks. See Figures 8.1.8.3. 2 in. (51 mm) required Continuous, non-combustible sealant Tile, stone or other non-combustible material Floor constructed of wood or other combustible material 1/2 in. Micore Hearth Ext or equivalent insulation (see Table 11.2) Fireplace Protective Metal Hearth Strip Figure 8.1 Hearth Extension Construction Protective metal strips are placed 2 in. (51 mm) under the front of the fireplace and must extend beyond the front and sides of fireplace opening by 2 in. (51 mm). 1 in. (25 mm) overlap Figure 8.2 Positioning the Protective Metal Hearth Strips The hearth extension should slope away from the front of the fireplace and chase at 1/8 in. to 1/4 in. per foot. Spark strips must be used on top of any combustible hearth materials used for moisture management. This fireplace has been tested and approved for use with a hearth extension insulated to a minimum R value of 1.03. To substitute materials for the factory-available hearth extensions, see Figure 8.3 and calculate insulation alternatives as per Table 8.1 and the following formulas: • Thermal conductivity per inch thickness = k • k = (BTU)(inch) / (foot2)(hour)(°F) • Required thickness = Rk • Thermal resistance per inch thickness = r • r = (foot2)(hour)(°F) / (BTU)(inch) • Required thickness = R / rB. A C B Figure 8.3 Hearth Extension Dimensions Fire Risk • Metal hearth strips MUST be installed. Sparks or embers may ignite flooring. WARNING Fire Risk • Hearth extensions must be installed exactly as specified. High temperatures or hot embers may ignite concealed combustibles. WARNING Table 8.1 CAT. # A B C HX3 in 52 16 8 mm 1321 406 203 HX4 in 66 20 12 mm 1676 508 305 Hearth Extension Insulation Alternatives-Total minimum R Value must equal 1.03 Material k per inch thick r per inch thick Minimum thickness required Hearth & Home HX3, HX4 (Micore 300™) 0.49 2.06 1/2 in. USG Micore 160™ 0.39 2.54 1/2 in. USG Durock™ Cement Board 1.92 0.52 2 in. Cement Mortor 5.0 0.20 5-1/8 in. Common Brick 5.0 0.20 5-1/8 in. Ceramic Tile 12.50 0.08 12-1/4 in. Armstrong™ Privacy Guard Plus 0.46 2.18 1/2 in. Marble 14.3-20.0 0.07-0.05 14-5/8 in. - 20-3/8 in. B. Finishing Material • Combustible Material Material which is made of or surfaced with wood, compressed paper, plant fibers, plastics, or any material capable of igniting and burning, whether flame proofed or not, plastered or not plastered. • Non-Combustible Material Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick,...
Ce manuel est également adapté pour les modèles :Cheminées - MONTANA MONTANA-36 (3.74 mb)