Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Remove control panel to operate middle clamp on 500 and 600 units. WARNING! HOT GLASS WILLCAUSE BURNS. DO NOT TOUCH GLASSUNTIL COOLED. NEVER ALLOW CHILDRENTO TOUCH GLASS. LOG PLACEMENT Before you begin — This unit is supplied with eight ceramic fiber logs. Do not handle these logs with your bare hands. Always wear gloves to prevent skin irritation from ceramic fibers. After handling the logs, wash your hands gently with soap and water to remove any traces of fibers. WARNING The positioning of the logs is critical to the safe and clean operation of this heater. Excessive sooting and other problems may result if the logs are not properly and firmly positioned in the appliance. Never add additional logs or embellishments such as pine cones or vermiculite to the heater. Only use the logs supplied with the unit. Failure to position the parts in accordance with diagrams below or to use only parts specifically approved for this heater may result in property damage or personal injury. Install logs and rock wool (ember material) in firebox 1. Remove glass frame. Refer to Glass Frame Removal, Page 31. 2. Carefully remove logs from wrapping. 3. Place left log (#1) on left end of grate. Line up two (2) pin holes in bottom of log with two (2) pins on grate. Log #1 will always be to the left of the control panel. Figure 41 4. Place right log (#2) on right end of grate. Line up three (3) pin holes in bottom of log with three (3) pins on grate. Figure 42 LG638DV6000 left log Grate LG639DV6000 right log Right Log (#2) Left Log (#1) Pins LG638 Control Panel Pins Figure 41 - Install Left Log (#1) Control Panel Figure 42 - Install Right Log (#2) 5. Position left end of bottom center back log (#3) beside rear end of left log (#1). Line up pin on grate with pin hole in bottom of center back log (#3) Snug right end of bottom center back log (#3) to the middle of right log (#2). Figure 43 6. Line up pin holes on bottom front log (#4) with pins on grate. Figure 44 7. Place back end of left top log (#5) on cutout of bottom front log (#4). Position front of left top log (#5) on grate prong two. Figure 45 log placement Bottom Center Back Log (#3) LG640DV6000 bot ctr back log Pin Bottom Front Log (#4) LG641bottom front log LG640 Pins Figure 43 - Install Bottom Center Log (#3) Left Top Log (#5) Figure 44 - Install Bottom Front Log (#4) LG641 Cutout of Bottom Front Log Figure 45 - Install Left Top Log (#5) Grate Prong Two LG642 8. Place Y-Shaped end of top log (#6) on on prong four of back of grate. Position other end of top log (#6) in cutout of bottom center log (#3). Figure 46 9. Break up rock wool (ember material) into dime-sized pieces. Place evenly across burner surface and mesh of grate. Figure 47. Do not exceed 1" depth of coverage. log placement L643DV6000 top log Top Log #6 Grate Prong Four Cutout on Bottom Center Log Control Panel Figure 46 - Install Top Log (#6) LG644DV6000 rockwool Figure 47 - Rock Wool Placement (Right Corner Model Shown) Rock Wool AIR RESTRICTOR ADJUSTMENT The fireplace is equipped with a restrictor plate that is located inside the top chamber of the fireplace. Depending upon the vent configuration, you may be required to adjust the restrictor position 1. Remove glass frame. Refer to Glass Frame Removal, Page 31. 2. Using a Phillips screw driver, loosen the screw that secures the air restrictor. Do not back the screw all the way out. 3. Slide the baffle on top of the restrictor plate to block a percentage of the grille opening. Refer to the chart below for recommended settings. Note: All the settings above are based on the testing at the factory and provided as a guide for startup. On certain applications, adding a restrictor disc will help to achieve flame aesthetics. FP2311air restrictor Flue Opening Air Restrictor Figure 48 - Adjust Baffle on Air Restrictor Plate Air Restrictor FP2311 Screw (Slide Left and Right) Venting Height (feet) % of Grille Opening 8 to 20 100% (Factory Setting) 20 to 30 75% 30 to 40 50% OPERATING INSTRUCTIONS for your safety read before lighting If you do not follow these instruction exactly, a fire or explosion may result causing property damage, personal injury or loss of life. WARNING A. This appliance is equipped with a pilot which must be lit with built-in battery ignitor while following these instructions exactly. B. BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS: • Turn off all gas to the appliance. • Open windows. • Do not attempt to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in, or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try t...
Ce manuel est également adapté pour les modèles :Cheminées - 624DV(ST (4.27 mb)
Cheminées - CR (4.27 mb)