Log:
Évaluations - 3, GPA: 3.7 ( )

Instructions Monessen Hearth, Modèle SSBV-4035CNE

Fabricant : Monessen Hearth
Taille : 4.4 mb
Nom Fichier :
Langue d'enseignement: enfr
Aller à la télécharger



Facilité d'utilisation


Note: Rotating the adjustment rod counterclockwise increases air and clockwise decreases air. . Light appliance (follow lighting procedure on lighting label in control compartment or see homeowners manual). . Allowtheburnertooperateforatleast15minutes while observing the flame continuously to ensure that the proper flame appearance has been achieved (see Figure 15). If the following conditions are present, adjust accordingly. • If flame appears weak or sooty, adjust the air shutter, incrementally, to a more open position until the proper flame appearance is achieved. • If flame stays lowered blue, adjust the air shutter, incrementally, to a more closed position until the proper flame appearance is achieved. 4. Leave the control knob (off/pilot/on) in the ON position and the burner OFF/ON switch OFF (& remote switches, if applicable). 5. When satisfied that the burner flame appearance is normal, close the lower control compartment door. WARNING Air shutter adjustment should only be performed by a qualified professional service technician. WARNING Ensurefrontglasspanelisinplace and sealed during adjustment. CAUTION The air shutter door and nearby appliance surfaces are hot. Exer cise caution to avoid injury while adjusting flame appearance. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Figure 16 CAUTION Carbonwillbeproducediftheair shutter is closed too much. Any damageduetocarboningresult ing from improperly setting the air shutter is not covered under the warranty. Burner Air Shutter Adjustment Adjustment Rod Up (Fully Open Position) Air Shutter Adjustment Rod Down (minimum air opening position) Burner Tube Adjustment Setscrew Main Burner Factory Air Shutter Opening Setting - Inches (millimeter) Model Natural Gas Propane Gas SSBV- 5 0 1/16" (1.58 mm) 1/4" (6. 5 mm) SSBV-40 5 1/16" (1.58 mm) 1/4" (6. 5 mm) Millivolt Appliance Checkout The pilot flame should be steady, not lifting or floating. Flame should be blue in color with traces of orange at the outer edge. The top 3/8" (10 mm) at the pilot generator (thermopile) and the top 1/8" minimum (tip) of the quick drop out thermocouple should be engulfed in the pilot flame. The flame should project 1" (25 mm) beyond the hood at all three ports. See Figure 17 or 18. To light the burner, refer to the lighting instructions on Pages 16 & 17. WIRING DIAGRAMS WIRING DIAGRAMS g diagrams are provided here for reference purposes only. This information is also provided on schematics attached directly to the appliance on a pullout panel located within the control compartment. CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous appliance operation. • Schematic Representation Only • If any of the original wire as supplied must BK be replaced, it must be replaced with Type AWM105 C - 18 gage wire. uOptional Kits -OFF/ON wall switch or remote control receiver. vAppliance mounted OFF / ON Switch BK Figure 20 -Millivolt Wiring Diagram Wiring Diagra...

Ce manuel est également adapté pour les modèles :
Cheminées - SSBV-3530CNE (4.4 mb)
Cheminées - SSBV-3530CNE (4.4 mb)
Cheminées - SSBV-3530CNM (4.4 mb)
Cheminées - SSBV-3530CNE (4.4 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories