Évaluations - 3, GPA: 3 ( )

Fabricant : Dimplex Taille : 353.81 kb Nom Fichier : Langue d'enseignement:

RESETTING THE TEMPERTURE CUTOUT SWITCH The heater on this fireplace is protected with a safety device to prevent overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset. It can be reset by switching the Main Power switch (FIGURE 2) to OFF and waiting 5 minutes before switching it to ON. CAUTION If you need to continuously reset the heater, disconnect the power at the main service panel and call your local dealer. NOTE The heater may emit a slight, harmless odor when first used. This odor is a normal condition caused by initial heating of internal heater parts and will not occur again. MAINTENANCE WARNING Disconnect all power coming to fireplace at main service panel before attempting an maintenance or cleaning to reduce risk of fire, shock or damage to persons. NOTE Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental burning of skin. TOOL REQUIREMENTS Slot screw driver LIGHT BULB REPLACEMENT Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental burning of skin. Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears. There are four bulbs under the log set which generate the flames and embers. LIGHT BULB REQUIREMENTS Quantity of 4 clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60 watt rating. Example: GE 60BC or Philips 60CTC. DO NOT EXCEED 60 WATTS PER BULB. CAUTION When handling log only apply force to the ember bed section not directly to the logs. HELPFUL HINTS It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace light bulbs. Long life bulbs are recommended to reduce the frequency of bulb changes. To access the light bulb area (BF33ST/DX, BF39ST/DX,BF45ST): 1. Open steel curtain (remove glass doors if applicable). 2. Remove two screws on log bracket and set aside. (FIGURE 3) 3. Pull front edge of plastic ember bed or plastic grate up and forward until rear tab releases from the ledge located at the bottom of the mirror. (FIGURE 4) Note: Log set fits tightly into firebox, some force may be necessary to remove. 4. Examine the bulbs to determine which bulbs require replacement. 5. Unscrew bulbs counter clockwise. 6. Insert new bulbs. 7. Replace the log by inserting the rear tab of the logset under the back ledge of the fireplace and push down on the front edge of the logset until it snaps into place. (FIGURE 4) 8. Replace log grate using two screws previously removed. SCREWS 6 FIGURE 3 FIGURE 4 To access the light bulb area (BF45DX) 1. Open steel curtain (remove glass doors if applicable). 2. Remove two screws on log bracket and set aside. (FIGURE 3) 3. Pull front edge of plastic ember bed or plastic grate up and forward until rear tab releases from the ledge located at the bottom of the mirror. (FIGURE 4) Note: Log set fits tightly into firebox, some force may be necessary to remove. 4. Set logset in front of firebox. 5. Disconnect the logset LED wire harness from unit. (FIGURE 5) 6. Examine the bulbs to determine which bulbs require replacement. 7. Unscrew bulbs counter clockwise. 8. Insert new bulbs. 9. Re-connect the logset LED wire harness to the unit. 10. Replace the log by inserting the rear tab of the logset under the back ledge of the fireplace and push down on the front edge of the logset until it snaps into place. (FIGURE 4) 11. Replace log grate using two screws previously removed. FIGURE 5 7 LED wire harness Mirror Cleaning The mirror is cleaned in the factory during the Assembly operation. During shipment, installation, Handling, etc., the mirror surface may collect dust Particles; these can be removed by buffing lightly With a clean dry cloth. To remove fingerprints or other marks, the mirror can be cleaned with a damp cloth using good quality household glass cleaner. The mirror should be completely dried with a lint free cloth to prevent water spots. To prevent scratching, do not use abrasive cleaners or spray liquids on the clear door surface. ACCESSORIES Please contact your local dealer for genuine Dimplex accessories. Example: Glass door kits, brass and stainless steel trims, remote control kits, plug kits, and cabinets designed to fit your fireplace. TWO YEAR LIMITED WARRANTY Products to which this limited warranty applies This limited warranty applies to the following models of your newly purchased Dimplex electric fireplace BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX, and to newly purchased Dimplex fireplace surrounds (mantels) and trims. This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA (and the District of Columbia) except for Hawaii and Alaska. This ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :