Évaluations - 1, GPA: 5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
To disconnect the cord (mains lead), pull it out by the plug. Never pull the cord itself. • Should any solid object or liquid fall into the component, unplug the tape deck and have it checked by qualified personnel before operating it any further. • The mains lead must be changed only at a qualified service shop. On placement • Place the tape deck in a location with adequate ventilation to prevent heat build-up in the tape deck. • Do not place the unit in an inclined position. • Do not place the unit in locations where it is: — Extremely hot or cold — Dusty or dirty — Very humid — Vibrating — Subject to direct sunlight Before placing a cassette in the tape deck Take up any slack in the tape. Otherwise the tape may get entangled in the parts of the tape deck and become damaged. When using a tape longer than 90 minutes The tape is very elastic. Do not change the tape operations such as play, stop, and fast-winding etc. frequently. The tape may get entangled in the tape deck. To save a tape permanently To prevent a tape from being accidentally recorded over, break off the cassette tab from side A or B as illustrated. If you later want to reuse the tape for recording, cover the broken tab with adhesive tape. Side A Tab of Tab of side A side B When you are using a TYPE II (CrO2) or TYPE IV (metal) cassette, be careful not to cover the detector slots which allow the tape player to automatically detect the type of tape. TYPE II TYPE IV Detector slots Cleaning the tape heads Clean the tape heads after every 10 hours of use. When the tape heads become dirty — the sound is distorted — there is a decrease in sound level — the sound drops out — the tape does not erase completely — the tape does not record. Make sure to clean the tape heads before you start an important recording or after playing an old tape. Use a separately sold dry-type or wet-type cleaning cassette. For details, refer to the instructions of the cleaning cassette. Demagnetizing the tape heads Demagnetize the tape heads and the metal parts that has contact with the tape after every 20 to 30 hours of use with a separately sold demagnetizing cassette. For details, refer to the instructions of the demagnetizing cassette. Cleaning the cabinet Use a soft cloth slightly moistened with mild detergent solution. Never use strong solvents, such as thinner or benzine, since they may damage the finish. If you have any questions or problems concerning your tape deck, please consult your nearest Sony dealer. TC-TX5 3-858-050-11 (1).EN Troubleshooting If you run into any problem using this tape deck, use the following check list. First, check that the mains lead is connected firmly and the speakers are connected correctly and firmly. Should any problem persist, consult your nearest Sony dealer. The cassette tray does not close. •Turn on the tape deck again and press ¤. The operating buttons on the tape deck do not work. •Press any of the operating buttons after the lamp on .stops flashing. (For approximately two seconds after the tape deck turns on, the buttons on the tape deck do not work.) •Reset the cassette and press ¤. The tape does not play or record. •There is slack in the tape. Take up any slack in the tape. •The heads are dirty. Clean them (see page 9). The tape does not record. •No cassette in the cassette tray. •The tab has been removed from the cassette (see page 9). •The tape has reeled to the end. The tape does not record nor play or there is a decrease in sound level. •The heads are dirty. Clean them (see page 9). •The record/playback heads are magnetized. Demagnetize them (see page 9). The tape does not erase completely. •The record/playback heads are magnetized. Demagnetize them (see page 9). TC-TX5 3-858-050-11 (1).EN There is excessive wow or flutter, or the sound drops out. •The capstans in the tape deck are dirty. Clean them (see page 9). Noise increases or the high frequencies are erased. •The record/playback heads are magnetized. Demagnetize them (see page 9). •Move the tape deck away from the TV or VCR. The sound is distorted. •Set DOLBY NR to the same setting as the tape was recorded. •Move the tape deck away from the TV or VCR. There is no sound. •The mains lead is disconnected from the wall outlet. •Make sure the connection of the audio connecting cords is correct. The remote does not work/Automatic Source Selection and/or One Touch Play does not work. •Make sure the connection of the AU BUS connecting cords is correct. The functions synchronized with the DHC-MD5 such as the CD Synchro Recording does not work. •Make sure the connection of the AU BUS connecting cord is correct. Specifications Recording system 4-track 2-channel stereo Frequency response (DOLBY NR OFF) 30 – 14,000 Hz ( ±3 dB), using Sony TYPE I cassette 30 – 15,000 Hz ( ±3 dB), using Sony TYPE II cassette Wow and flutter ±0.15% W. Peak (IEC) 0.1% W. RMS (NAB) ±0.2% W. Peak (DIN) Input TAPE IN (phono jacks): impedance 47 kilohms Output TAPE OUT (phono jacks): voltage 550 mV im...