Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Your milk froths up. STEAM INTAKE When the required amount of froth has been attained push selector key anew. COFFEE READY E 11 With the flow-adjustment you can set the optimum frothing. Turn the handle slightly to the right or to the left until you obtain the required result. 11.3 Drawing off hot milk using the Auto-Cappuccinatore S9 The Auto-Cappuccinatore of the S9 can be used to draw off hot milk. Adjust the selector lever (1) (Fig. 10) to position (3) to draw off hot milk. Install the Auto-Cappuccino. This is included in your Welcome Pack. 11.4 Drawing off cappuccino using the Auto-Cappuccintore S9 The Auto-Cappuccinatore of the S9 can be used to draw off capuccino. Adjust the selector lever (1) (Fig. 10) to position (2) to draw off capuccino. 11.5 Controlling the temperature using the Auto-Cappuccinatore S9 Adjust the selector lever (1) to + for hot milk/cappuccino or -for less hot milk/cappuccino. Individual fine adjustment is possible. 11.6 Cleaning the Auto-Cappuccinatore Remove Auto-Cappuccinatore (21). If you do not achieve optimum results, disassemble the flow controller and the selector lever (Fig. 10 for S9). Thoroughly rinse these parts with water. As soon as you have frothed enough milk, it is important to clean the Auto-Cappuccino. Fill water in a jug and immerse the intake-tube in the water. Now draw off steam until the water/steam mixture flowing into your cup is completely clean. Your Auto-Cappuccino is clean again. 12. Switching off machine When the machine is switched off, the rinsing program is automatically run again. Therefore place an empty container under the coffee-spout (15) and press ON/OFF key . When the rinsing water has run into the container, the machine powers down. Discard the water. 13. Programming Before leaving our factory, the machine is adjusted to enable you to obtain coffee without any additional programming. In order to adapt the result to your personal taste, various settings can be programmed individually. The programming keys are located behind the front cover (3). The following settings can be programmed: Powder quantity Coffee temperature Water quantity Steam portion Tea portion Filter Water hardness Economy mode Timer clock Automatic switch on time Automatic switch off time Supplies and cup counter Language selection 13.1 Programming powder quantity The selected value is confirmed Now your machine prepares a coffee. Switch the machine on by pressing ON/OFF key . P ENOUGH COFFEE? / PRESS KEY Press key until you can hear an acoustic signal. P OK? -P ·········· II ·········· POWDER QUANTITY / SELECT KEY + When the required water quantity is reached press key P . You 1 cup only. The corresponding quantity for 2 cups is adjusted Now press the key that you want to programme. Use the key for can call up the next setting by pressing key + . automatically by the machine after programming is finished. There is an additional possibility to alter the water quantity anew. Press key + or - for this purpose. - ·········· II ·········· POWDER + If you wish to draw another coffee to control the water quantity, + - press key again otherwise press key P briefly to store water briefly. The powder quantity can be selected by pressing keys or quantity in memory. P By pressing the + button, you can select the next phase, or press the To store the new powder quantity in memory briefly press key . button in order to leave the programming. POWDER QUANTITY / SELECT KEY. N By pressing the + button, you can select the next phase, or N 13.4 Programming steam portion press the button in order to leave the programming. STEAM PORTION 13.2 Programming coffee temperature Press key PORTION /....20 SEC. TEMPERATURE COFFEE / SELECT KEY By pressing key + or - you can programme time in seconds (drawing off time of 3 – 250 sec.) Now press the key that you want to programme. Select the required temperature (high or normal) by activating key + - Press key P . or . STEAM PORTION P . By pressing the To store the new coffee temperature in memory briefly press key + button, you can select the next phase, or button in order to leave the programming. TEMPERATURE COFFEE / SELECT KEY press the N By pressing the + button, you can select the next phase, or N 13.5 Programming tea portion press the button in order to leave the programming. Place a cup under the height-adjustable tea-spout (22). Press key 13.3 Programming water quantity OPEN TAP WATER QUANTITY / SELECT KEY ENOUGH TEA? / CLOSE TAP Put a cup under the coffee-spout (15) and then press the key that TEA PORTION you want to programme. E .P .P 13 The required portion of tea-water is programmed now. By pressing the + button, you can select the next phase, or press the N button in order to leave the programming. 13.6 Programming Filter Please read chapter 7.1 “Placing filter“. 13.7 Programming water hardness (only with setting Filter no) HARDNESS LEVEL 3 Press key P By pressing key or + P + briefly you can pr...