Évaluations - 3, GPA: 4.3 ( )

Fabricant : Jura Capresso Taille : 291.2 kb Nom Fichier : Langue d'enseignement:

Should you get descaling agent in your eyes, consult a doctor. • Immediately remove any splashes or drops of the decalcifying agent from sensitive surfaces, such as natural stone or wood. • Always wait until the decalcifying agent in the water tank has been used up. Do not fill additional decalcifying agent into the water tank. • Never use vinegar or any other decalcifying agent. This might damage internal parts of the machine. When the display shows DE-SCALE / READY it is time to decalcify the machine. You can still make coffee. However, it is highly recommended decalcifying the machine within the next 3 to 4 days. Important: CLEARYL FILTER: If you use the Clearyl water cartridge and the display shows DE-SCALE / READY, then your cartridge function was not activated. Follow the instructions in chapter 17.1 to activate a new cartridge. Important: The decalcifying program must not be interrupted. DE-SCALE / READY 1. Remove the Dual Frother or the frothXpress from the steam nozzle (Fig. 17). 2. Open the cover behind the Rotary Dial and press the Rinse button (Fig. 4) The display shows EMPTY TRAY. 3. Remove the complete drawer with the grid and the used coffee container (Fig. 1, 12 to 14) and empty the tray and the used coffee container. 25. 4. Replace the complete assembly. 5. The display shows AGENT IN TANK. 6. Remove and empty the water tank. (The Clearyl filter should not be in the water tank!) 7. Dissolve 3 of the large square decalcifying tablets in a container with 18 oz. of water (0.5 liters) and pour the solution into the water tank and replace. 8. The display shows OPEN TAP. 9. Place a 20 oz. container under the steam nozzle (Fig. 17). 10. Turn the selector switch to the hot water/steam position. The display shows DE-SCALING. Descaling agent flows through the steam nozzle in intervals and will stop automatically after a few minutes. 11. When the display shows CLOSE TAP, turn the Selector Switch to the Coffee symbol. The display shows DE-SCALING and the descaling agent cleans internal parts and releasing it into the ground coffee container and tray. This takes several minutes. 12. When the display shows EMPTY TRAY, remove the outside container, then carefully remove the drawer and empty the used coffee container and tray and replace all. 13. The display shows FILL WATER TANK. Remove the water tank, rinse thoroughly, fill with 16 oz. of fresh, cold water and replace. The display shows OPEN TAP. 14. Place a 20 oz. container under the steam nozzle (Fig. 17) and turn the Selector Switch to the hot water/steam position. The display shows DE-SCALING. Clean water will push through the steam nozzle removing all descaling liquids. 15. When display shows CLOSE TAP, turn the Selector Switch to the Coffee symbol. The display shows DE-SCALING and the cleaning procedures continues internally. 16. When the display shows EMPTY TRAY, remove the outside container, then carefully remove the drawer and empty the used coffee container and tray and replace all. READY. 17. Re-attach the Dual Frother or the frothXpress to the steam nozzle. The machine will automatically remind you when it’s time to decalcify again. 18.4 MANUAL DECALCIFYING If you use very hard water it is possible that calcium builds up prematurely. If your coffee does not come out as hot as before it is a sign for calcium build-up. When this happens you can manually start a decalcifying cycle as follows: READY • Push and hold the P button (Fig. 4) until the display shows RINSE. • Push the P button again. The display shows again RINSE. • Turn the Rotary Dial until the display shows DE-SCALE. • Push the Rotary Dial EMPTY TRAY. • Continue with steps 3 through 17 in chapter 18.3 18.5 RINSE CYCLE, MANUALLY When you turn the ENA on, the display turns from HEATING to PRESS ROTARY. This will perform an initial rinse cycle. When the ENA is turned off, the system automatically rinses the machine if coffee had been brewed before. Rinsing can also be initiated manually, e.g. after using pre-ground flavored coffee. Place a cup underneath the coffee spouts. ENA 5 only: turn the coffee spout to the rinsing position (Fig. 11). 26. READY. • Push and hold the P button (Fig. 4) until display shows RINSE. • Push the P button again. The display again shows RINSE. • Push the P button a third time. The display shows RINSING. After a few seconds the rinse cycle stops automatically. READY. ENA 5 only: turn the spout again to the 1- or 2-cup position. 19. ENERGY SAVING MODE The ENA is set to ENERGY – . This means the machine is always ready to brew coffee without any wait. You can program an energy savings mode. Five minutes after the last brewing the ENA lowers the stand-by temperature. In case you want to brew coffee the machine will then heat up for approx. 30 seconds. To change the energy setting: READY, • Push and hold the P button (Fig. 4) until the display shows RINSE. • Turn the Rotary Dial until the display shows ENERGY • Push the Rotary Dial ECONOMY – • Turn the Rotary Dial...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :